Timber-concrete composite systems are a high-performance alternative for building floors, of great interest in the current context of environmental concerns. Looking for a more eco-friendly solution, the paper presents a new flooring system with a wood-concrete connection that does not require adhesives or special metal elements. Four-point bending tests were performed on TCC flooring samples with a span of 6.0, 7.2 and 8.4 m. Its cross section was a prefabricated piece in the shape of an inverted T made up of a lower glulam flange, glued together with a central plywood rib with aligned holes in its upper part that go through the entire thickness of the plywood. The set was completed with a top layer of poured-in-place concrete. The connection between both materials is achieved by penetrating the concrete into the rib holes. Additionally, corrugated steel bars were placed through said holes to achieve ductile behaviour. In all cases, a slenderness ratio of L/24 was used. The experimental results showed that the lowest value of ultimate load obtained was 4.3 times higher than the total service load estimated for a building for public use (9 kN/m2). The maximum deflection of the total load was between L/573 and L/709 for the loads corresponding to a building for public use (9 kN/m2) and between L/1069 and L/1340 for the case of residential type building (5 kN/m2). An analysis of the effects of vibrations in the service limit state in relation to user comfort has been included. The results indicate that the system satisfies the requirements for the intended uses.
Consequently, the proposed solution shows its effectiveness both in terms of strength and stiffness for the construction of light floors, being easy to build and having high performance.
Experimental and theoretical investigation on shear performances of glued-in perforated steel plate connections for prefabricated timber–concrete composite beams
Glued-in perforated steel plate (GIPSP) connections demonstrate significant shear strength and high slip modulus. Consequently, they indicate substantial potential for application in timber–concrete composite (TCC) structures according to the emerging tendencies in high-storey and large-span buildings. However, the application pattern in prefabricated TCC structures and the theoretical analysis of the shear performances of GIPSP connections are highly deficient. This hinders the application of this type of shear connection. In this study, the shear performances of GIPSP connections were evaluated using push-out tests. Ten groups of push-out specimens with different steel plate numbers, steel plate lengths, and concrete slab types were tested. The concrete slab types investigated in the experiments included a prefabricated concrete slab and cast-in-situ concrete slab. The experimental results were discussed in terms of the failure mode, load-carrying capacity, and slip modulus. The theoretical models for the load-carrying capacity related to the associate failure mode were discussed based on an analysis of the failure mechanisms. In addition, design proposals with regard to the load-carrying capacity and slip modulus of the GIPSP connection were presented. The research results can provide design guidance for TCC beams using GIPSP connections and prefabricated concrete slabs.
5th International Conference: Innovative Materials, Structures and Technologies (IMST 2022)
Research Status
Complete
Series
Journal of Physics: Conference Series
Summary
With the growing importance of the principles of sustainable construction, the use of load-bearing timber-concrete composite structures is becoming increasingly popular. Timber-concrete composite offers wider possibilities for the use of timber in construction, especially for large-span structures. The most significant benefit from combining these materials can be obtained by providing a rigid connection between the timber and concrete layers, which can be obtained by the adhesive timber-to-concrete connection produced by the proposed stone chips method. A sustainable solution involves the abandonment of steel longitudinal reinforcement. The use of such a solution in practice is often associated with fears of a fragile collapse. Therefore, the issue of how to increase the safety factor of the proposed material is topical now. The experimental investigation is made to determine the effect of synthetic fibre use on timber-concrete composite behaviour by testing a series of timber-concrete composite specimens with and without fibres in the concrete layer. The obtained results show that adding 0.5 % of synthetic macro fibres allows to abandon the use of longitudinal steel reinforcement and prevents the formation of large cracks in concrete and the disintegration of the concrete layer in case of collapse.
Comparing the environmental impacts of building materials at the building level can be biased because a building design is optimized for a primary structural material. To achieve objective comparisons, this study compares the environmental impact of reinforced concrete (RC), cross-laminated timber (CLT), and timber-concrete composite (TCC) at the component level with equivalent structural performance. A slab was selected as the target structure member because its design does not consider lateral forces. Equivalent structural performance was defined as the minimum quantity of slab materials for comparable span and live load conditions. The functional unit for this study was defined as a 1 m2 slab. The system boundary covered the cradle-to-gate perspective, including raw material extraction, transportation, and manufacturing. The structural design method and material design values followed the Korean building code and standards. Environmental product declaration data developed in Korea were used to evaluate the carbon footprint. The CLT emitted 75 % less carbon dioxide, the primary greenhouse gases responsible for anthropogenic climate change, compared with RC regardless of conditions, while the TCC emitted 65 % less CO2, and its environmental impact improved as the span lengthened. The results also indicated that timber slabs are thinner than concrete slabs and can be structurally rational.
Dimensional behavior of nail-laminated timber-concrete composite caused by changes in ambient air, and correlation among temperature, relative humidity, and strain
A timber-concrete composite (TCC) slab composed of nail-laminated timber (NLT) and topping concrete (TC) was developed for flooring applications. The NLT was laminated alternately with lumber and plywood. To investigate the dimensional behavior of the TCC slab, the temperature, relative humidity (RH), and dimensional changes of the slab exposed to outdoor air were monitored for 205 days. Temperature change was directly transmitted to both components, and RH change was gradually transmitted to the NLT. Concrete pouring caused a sharp increase in NLT width, which was the laminating direction of the nails. This resulted from swelling of the wood because of the moisture in the concrete mixture and loosening of the nail lamination. The member composition for the nail-laminating system, fastener type, and concrete volume help to secure the dimensional stability of the NLT. Cracks in the TC caused width deformation, which was recovered by drying shrinkage of the TC. Correlation analysis among temperature, RH, and strain indicated that dimensional changes in NLT correlated strongly with RH, while those in TC correlated strongly with temperature. The correlation between longitudinal strain in the TC and strain in the three directions of the NLT was attributed to the notches designed for mechanical connection.
An integrated solution is presented for the execution of building structures using timber-concrete composite (TCC) sections that make efficient use of the mechanical properties of both materials. The system integrates flooring and shaped prefabricated beams composed of a lower flange of glued laminated timber (GLT) glued to one or more plywood or laminated veneer lumber (LVL) ribs and linked to an upper concrete slab poured in situ. The parts may be prefabricated in T shape (only one rib), in p shape (two ribs), or with multiple ribs to create wider pieces, thereby reducing installation operations.
The basis of the system is the timber-concrete shear connection in the form of holes through the ribs, which are filled by the in situ-poured concrete. The connection is complemented with the arrangement of reinforcement bars through the holes.
Three test campaigns were undertaken. Shear tests of the timber-concrete connection in 12 test pieces. Shear test along the wood-wood glue line (72 planes tested) and wood -plywood (24 planes tested). Delamination test of the glued planes (24 wood-wood planes and 8 wood-plywood planes). The results indicate a high strength joint, with ductile failure and high composite effect. Likewise, the shear test results along the glue line and the delamination tests show section integrity under demanding hygrothermal conditions.
Preliminary sizing curves were developed considering the Gamma Method to evaluate the performance of the system. The results show the possibilities of the system, as pouring the upper slab concrete in situ makes it possible to create continuous semi-rigid joints between the elements. This gives rise to slender flooring structures, light and with high stiffness plane against horizontal forces.
With the growing importance of the principle of sustainability, there is an increasing interest in the use of timber–concrete composite for floors, especially for medium and large span buildings. Timber–concrete composite combines the better properties of both materials and reduces their disadvantages. The most common choice is to use a cross-laminated timber panel as a base for a timber–concrete composite. But a timber–concrete composite solution with plywood rib panels with an adhesive connection between the timber base and fibre reinforced concrete layer is offered as the more cost-effective constructive solution. An algorithm for determining the rational parameters of the panel cross-section has been developed. The software was written based on the proposed algorithm to compare timber–concrete composite panels with cross-laminated timber and plywood rib panel bases. The developed algorithm includes recommendations of forthcoming Eurocode 5 for timber–concrete composite design and an innovative approach to vibration calculations. The obtained data conclude that the proposed structural solution has up to 73% lower cost and up to 71% smaller self-weight. Thus, the proposed timber–concrete composite construction can meet the needs of society for cost-effective and sustainable innovative floor solutions.
ICSI 2021 The 4th International Conference on Structural Integrity
Research Status
Complete
Series
Procedia Structural Integrity
Summary
Rigid timber to concrete connection is the most effective solution for timber-concrete composite members subjected to the flexure which provides full composite action and better structural behaviour. One of the most used technologies to produce glued connection of the timber-concrete composite is “dry” method, which includes gluing together of timber and precast concrete slab. This technique has high risk of forming a poor-quality rigid connection in timber-concrete composite, and there are difficulties in controlling the quality of the glued connection. The effect of the non-glued areas in connection between composite layers on the shear stresses and energy absorption were investigated by finite element method and laboratorian experiment. Three timber-concrete composite panels in combination with carbon fibre reinforced plastic composite tapes in the tension zone with the span 1.8 m were statically loaded till the failure by the scheme of three-point bending. Mid-span displacements were measured in the bending test. One specimen was produced by dry method, by gluing together cross-laminated timber panel and prefabricated concrete panel. Timber-concrete qualitative connection of the other two specimens was provided by the granite chips, which were glued on the surface of the cross-laminated timber by epoxy, and then wet concrete was placed. Dimensions of the crushed granite pieces changes within the limits from 16 to 25 mm. The investigated panel with different amount and sizes of non-glued areas in the timber to concrete connection was numerically modelled. Obtained results shown, that the increase of shear stresses is influenced not so much by a total amount of non-glued areas, but by the size of the individual defective areas. Moreover, large non-glued areas significantly reduce the energy absorption of elements subjected to the flexure, which was observed experimentally for defective panel produced by the classical dry method with almost 4 times larger mid-span displacements than for panel with full composite action provided by the proposed production technology of the timber to concrete rigid connection. So, the proposed technology based on the use of granite chips, provides a high-quality connection between timber and concrete layers, with insignificant ration between possible defect and total connection surface area, which is equal to the area of one granite chips edge.
In the construction of modern multi-storey mass timber structures, a composite floor system commonly specified by structural engineers is the timber–concrete composite (TCC) system, where a mass timber beam or mass timber panel (MTP) is connected to a concrete slab with mechanical connectors. The design of TCC floor systems has not been addressed in timber design standards due to a lack of suitable analytical models for predicting the serviceability and safety performance of these systems. Moreover, the interlayer connection properties have a large influence on the structural performance of a TCC system. These connection properties are often generated by testing. In this paper, an analytical approach for designing a TCC floor system is proposed that incorporates connection models to predict connection properties from basic connection component properties such as embedment and withdrawal strength/stiffness of the connector, thereby circumventing the need to perform connection tests. The analytical approach leads to the calculation of effective bending stiffness, forces in the connectors, and extreme stresses in concrete and timber of the TCC system, and can be used in design to evaluate allowable floor spans under specific design loads and criteria. An extensive parametric analysis was also conducted following the analytical procedure to investigate the TCC connection and system behaviour. It was observed that the screw spacing and timber thickness remain the most important parameters which significantly influence the TCC system behaviour.
This thesis focuses on the structural performance of mass timber panel-concrete composite floors with notches. Mass timber panels (MTPs) such as cross-laminated timber, glue-laminated timber, and nail-laminated timber, are emerging construction materials in the building industry due to their high strength, great dimensional stability, and prefabrication. The combination of MTPs and concrete in the floor system offers many structural, economic, and ecological benefits. The structural performance of MTP-concrete composite floors is governed by the shear connection system between timber and concrete. The notched connections made by cutting grooves on timber and filling them with concrete are considered as a structurally efficient and cost-saving connecting solution for resisting shear forces and restricting relative slips between timber and concrete. However, the notched connection design in the composite floors is not standardized and the existing design guidelines are inadequate for MTP-concrete composite floors.
To study the structural performance of notched connections and notch-connected composite floors, this thesis presented experimental, numerical, and analytical investigations. Push-out tests were conducted on the notched connections first, and then bending tests and vibration tests were conducted on full-scale composite floors. Finite element models were built for the notched connections to derive the connection shear stiffness. Finally, analytical solutions were developed to predict the internal actions of the composite floors under external loads.
This study shows that the structural performance of notched connections is affected by the geometry of the connections and material properties of timber and concrete. The notch-connected MTP-concrete composite floors showed high bending stiffness but were not fully composite. The floors with shallow notches tended to fail in a ductile manner but had lower bending stiffness than floors with deep notches. The composite floors with deep notches, however, often fail abruptly in the concrete notches. By reinforcing the notched connections with steel fasteners, the composite floor can achieve high bending stiffness, high load-carrying capacity, and controlled failure pattern. The proper number and locations of notched connections in the composite floors can be determined from the proposed composite beam model.
This thesis presented promising results in terms of the static and dynamic structural performance of notch-connected MTP-concrete composite floors. The test investigations added additional data to the current research body and prompted further evolvement of timber-concrete composite floors. The proposed empirical equations for estimating the connection stiffness and strength and composite beam model for predicting the serviceability and ultimate structural performance of composite floors provide useful tools to analyze the notch-connected MTP-concrete composite floors. The design recommendations for MTP-concrete composite floors with notches are provided in the thesis.
+System+with+Mechanical+Connectors){kind=link}
