This paper presents an investigation of possible disproportionate collapse for a nine-storey flat-plate timber building, designed for gravity and lateral loads. The alternate load-path analysis method is used to understand the structural response under various removal speeds. The loss of the corner and penultimate ground floor columns are the two cases selected to investigate the contribution of the cross-laminated timber (CLT) panels and their connections, towards disproportionate collapse prevention. The results show that the proposed building is safe for both cases, if the structural elements are removed at a speed slower than 1 sec. Disproportionate collapse is observed for sudden element loss, as quicker removal speed require higher moments resistance, especially at the longitudinal and transverse CLT floor-to-floor connections. The investigation also emphasises the need for strong and stiff column-to-column structural detailing as the magnitude of the vertical downward forces, at the location of the removed columns, increases for quicker removal.
This paper presents the preliminary design of a rocking Cross-laminated Timber (CLT) wall using a displacement-based design procedure. The CLT wall was designed to meet three performance expectations: immediate occupancy (IO), life safety (LS), and collapse prevention (CP). Each performance expectation is defined in terms of an inter-story drift limit with a predefined non-exceedance probability at a given hazard level. U-shape flexural plates were used to connect the vertical joint between the CLT panels to obtain a ductile behavior and adequate energy dissipation during seismic motion. A design method for ensuring self-centering mechanism is also presented.
March 29-31, 2012, Chicago, Illinois, United States
This paper describes initial experimental testing to investigate feasible sources of passive damping for the seismic design of post-tensioned glue laminated timber structures. These innovative high performance structural systems extend precast concrete PRESSS technology to engineered wood structures, combining the use of post-tensioning bars or cables with large post-tensioned timber members. The combination of these two elements provides elastic recentering to the structure while the addition of damping using a specialised energy dissipation system gives the desirable `flag shaped' hysteretic response under lateral loading. Testing has been performed on a full scale beam-column joint at the University of Basilicata in Italy in a collaborative project with the University of Canterbury, New Zealand. The experimental testing uses engineered wood products, extending the use of laminated veneer lumber (LVL) structures tested in New Zealand to testing of glue laminated timber (glulam) structures in Italy. Current testing is aimed at further improvement of the system through additional energy dissipation systems.
A new type of mass timber structural system has been developed in New Zealand over the last decade. Timber members made of engineered wood products are used in combination with post-tensioning cables to produce highly efficient structural components suitable for multi-story moment resisting frames or shear wall-based lateral load resisting systems. Both systems are particularly useful in structures designed in high seismic regions. The post-tensioning also ensures self-centering of the components and the structural systems after a seismic event. In addition to the post-tensioning, the systems can use energy dissipating devices within the connections that further enhance the ductility of the systems and make them good candidates for low damage structural applications. Extensive experimental and numerical studies have been conducted to determine the performance of these systems and design procedures have been developed for practical applications. In an effort to bring this system closer to the North American designers, this paper contains a summary of the evolution of the concept and the most important research projects and findings to date. In addition, a number of applications within and outside New Zealand are reviewed to demonstrate the applicability of the concept. Finally, potential and recent initiatives for adoption of the technology in North America are discussed.
This paper presents the seismic design and analysis of a 20-storey demonstration wood building, which was conducted as a part of the NEWBuildS tall wood building design project. A hybrid lateral load resisting system was chosen for the building. The system consisted of shear walls and a shear core, both made of structural composite lumber, connected with dowel-type connections and heavy-duty HSK (wood-steel-composite) system. The core and the shear walls were linked with horizontal steel beams at each floor. The wood-based panel-to-panel interface was designed to be the main energy dissipating mechanism of the system. A detailed finite element model of this building was developed and non-linear time history analyses were performed using 10 earthquake motions. The results showed that the seismic response of the 20-storey demonstration building met the various design criteria and the design details are appropriate.
April 3-5, 2014, Boston, Massachusetts, United States
Cross-laminated timber (CLT) is widely perceived as the most promising option for building high-rise wood structures due to its structural robustness and good fire resistance. While gravity load design of a tall CLT building is relatively easy to address because all CLT walls can be utilized as bearing walls, design for significant lateral loads (earthquake and wind) can be challenging due to the lack of ductility in current CLT construction methods that utilize wall panels with low aspect ratios (height to length). Keeping the wall panels at high aspect ratios can provide a more ductile response, but it will inevitably increase the material and labor costs associated with the structure. In this study, a solution to this dilemma is proposed by introducing damping and elastic restoring devices in a multi-story CLT building to achieve ductile response, while keeping the integrity of low aspect ratio walls to reduce the cost of construction and improve fire resistance. The design methodology for incorporating the response modification devices is proposed and the performance of the as-designed structure under seismic is evaluated.