Skip header and navigation

2 records – page 1 of 1.

A Contribution to the Design of Ribbed Plates

https://research.thinkwood.com/en/permalink/catalogue1692
Year of Publication
2016
Topic
Design and Systems
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Glulam (Glue-Laminated Timber)
Author
Augustin, Manfred
Zimmer, Severin
Bogensberger, Thomas
Sleik, Tim
Year of Publication
2016
Format
Conference Paper
Material
CLT (Cross-Laminated Timber)
Glulam (Glue-Laminated Timber)
Topic
Design and Systems
Mechanical Properties
Keywords
Ribbed Plates
Elastic Model
Shear Stresses
Tensile Stresses
Notches
Conference
World Conference on Timber Engineering
Research Status
Complete
Notes
August 22-25, 2016, Vienna, Austria p. 4262-4271
Summary
The topic of this paper is the discussion of a proposal for the design of ribbed plates built-up with CLT (plate)- and GLT (ribs)- members. The suggested elastic model is based on the work of Abdelouahed [13] and Smith and Teng [14] for the strengthening of concrete members with FRP plates and will be applied for the mentioned loadcarrying timber elements. As a result so far it could be observed, that high peaks of shear and tensile stresses perpendicular to the interface (glue-line) occur due to the elastic consideration of the material. The model was evaluated by some pre-test which showed an acceptable correlation between the predictions of the model and a 2D-FEM analysis. It is evident, that the notches at the end of the rips must be reinforced by e.g. self-tapping screws or glued in rod to achieve effective solutions for this load carrying element. With the discussed model the shear and tensile stresses and forces resp. perpendicular to the interface can be computed.
Online Access
Free
Resource Link
Less detail

In Plane Shear Strength of Cross Laminated Timber (CLT): Test Configuration, Quantification and influencing Parameters

https://research.thinkwood.com/en/permalink/catalogue2121
Year of Publication
2013
Topic
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Application
Wood Building Systems
Author
Brandner, Reinhard
Bogensberger, Thomas
Schickhofer, Gerhard
Organization
Graz University of Technology
Year of Publication
2013
Format
Conference Paper
Material
CLT (Cross-Laminated Timber)
Application
Wood Building Systems
Topic
Mechanical Properties
Keywords
Shear Resistance
Shear Loads
In-Plane Shear Strength
Single Nodes
Net-Shear
Conference
International Council for Research and Innovation in Building and Construction, Working Commission W18 - Timber Structures
Research Status
Complete
Summary
Cross laminated timber (CLT) has become a well-known and widely applied two-dimensional, engineered timber product worldwide. It constitutes a rigid composite of an odd number of orthogonal and glued layers. Focusing on a single glued node loaded in plane in shear and composed of two crossed board segments and the adhesive layer in-between, in principle three types of shear mechanisms can be distinguished: mechanism I "net-shear" (shearing perpendicular to grain), mechanism II "torsion" and mechanism III "gross-shear" (shearing parallel to grain). In fact, while having generally accepted values for the resistance against mechanism II and good estimates for mechanism III the resistance against "net-shear" (mechanism I) is still in discussion. In spite of numerous investigations on nodes and on whole CLT elements in the past, a common sense concerning the test procedure, the consideration and handling of distinct influencing parameters and the quantification of the shear strength are open. We focus on the in plane shear resistance of single nodes according to mechanism I. We (i) propose a test configuration for reliable determination of the shear strength, (ii) determine the shear resistance in case of shear loads perpendicular to grain, (iii) discuss influences of some parameters on the shear strength of single nodes, and (iv) give a brief outlook concerning the resistance of CLT elements against shear loads in plane.
Online Access
Free
Resource Link
Less detail