Skip header and navigation

32 records – page 1 of 4.

Analysis of Mechanical Properties of Cross-Laminated Timber (CLT) with Plywood using Korean Larch

https://research.thinkwood.com/en/permalink/catalogue1806
Year of Publication
2018
Topic
Mechanical Properties
Material
CLT (Cross-Laminated Timber)

An Analytical Model for Design of Reinforcement around Holes in Laminated Veneer Lumber (LVL) Beams

https://research.thinkwood.com/en/permalink/catalogue135
Year of Publication
2013
Topic
Design and Systems
Mechanical Properties
Material
LVL (Laminated Veneer Lumber)
Application
Beams
Author
Ardalany, Manoochehr
Fragiacomo, Massimo
Moss, Peter
Deam, Bruce
Publisher
Springer Netherlands
Year of Publication
2013
Country of Publication
Netherlands
Format
Journal Article
Material
LVL (Laminated Veneer Lumber)
Application
Beams
Topic
Design and Systems
Mechanical Properties
Keywords
Failure
Glued-In Rods
Model
Reinforcement
Screws
Tensile
Language
English
Research Status
Complete
Series
Materials and Structures
ISSN
1871-6873
Summary
Openings are usually required to allow services like plumbing, sewage pipes and electrical wiring to run through beams. This prevents an extra depth of the floor/ceiling, while preserving architectural considerations. The introduction of large opening causes additional tension perpendicular to grain in timber beams. The low tensile strength perpendicular to grain of wood allows crack formation. Crack propagation around the hole considerably decreases the load-carrying capacity of the beam. However, in most cases, crack formation and propagation around the hole can be prevented by the use of an appropriate reinforcement. Screw, glued-in rods, and plywood are alternative options for the reinforcement. Design of the reinforcement requires that the working mechanism of the reinforcement is fully understood and properly addressed. In addition, reinforcement should be designed for actions produced in the section of the beam weakened by the hole. The current paper uses a simple truss model around the opening to calculate the tensile force in the reinforcement. Two simple formulations for design of the reinforcement are derived and compared with numerical and experimental results, showing an overall good correspondence. The proposed truss model can be considered for incorporation in future codes of practice.
Online Access
Free
Resource Link
Less detail

An Evaluation of Strength Performance of the Edge Connections between Cross-laminated Timber Panels Reinforced with Glass Fiber-reinforced Plastic

https://research.thinkwood.com/en/permalink/catalogue2424
Year of Publication
2019
Topic
Connections
Material
CLT (Cross-Laminated Timber)
Application
Wood Building Systems

Comparison of Verification and Reinforcement Concepts for Timber Beams with Large Round Holes

https://research.thinkwood.com/en/permalink/catalogue1714
Year of Publication
2016
Topic
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Glulam (Glue-Laminated Timber)
Application
Beams
Author
Dröscher, Julia
Augustin, Manfred
Schickhofer, Gerhard
Year of Publication
2016
Country of Publication
Austria
Format
Conference Paper
Material
CLT (Cross-Laminated Timber)
Glulam (Glue-Laminated Timber)
Application
Beams
Topic
Mechanical Properties
Keywords
Reinforcement
Shear Stresses
Tensile Stresses
Load Carrying Capacity
Numerical Investigation
Analytical Investigation
Language
English
Conference
World Conference on Timber Engineering
Research Status
Complete
Notes
August 22-25, 2016, Vienna, Austria p. 4529-4538
Summary
Within this paper a comparison of different reinforcement concepts for timber beams with round holes is carried out. Therefore currently applied standardized methods and two recently developed approaches are considered. By means of numerical and analytical investigations it becomes apparent that the analysed reinforcement methods divergent to those given in current standards have great potential: shear stresses as well as tensile stresses perpendicular to the grain in the critical areas around the beam opening can be reduced significantly. Hence, the maximum load carrying capacities of the new reinforcement concepts supposedly exceed the standardized ones considerably. For verification of the results experimental investigations on beams with different reinforcement methods are planned.
Online Access
Free
Resource Link
Less detail

A Contribution to the Design of Ribbed Plates

https://research.thinkwood.com/en/permalink/catalogue1692
Year of Publication
2016
Topic
Design and Systems
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Glulam (Glue-Laminated Timber)
Author
Augustin, Manfred
Zimmer, Severin
Bogensberger, Thomas
Sleik, Tim
Year of Publication
2016
Country of Publication
Austria
Format
Conference Paper
Material
CLT (Cross-Laminated Timber)
Glulam (Glue-Laminated Timber)
Topic
Design and Systems
Mechanical Properties
Keywords
Ribbed Plates
Elastic Model
Shear Stresses
Tensile Stresses
Notches
Language
English
Conference
World Conference on Timber Engineering
Research Status
Complete
Notes
August 22-25, 2016, Vienna, Austria p. 4262-4271
Summary
The topic of this paper is the discussion of a proposal for the design of ribbed plates built-up with CLT (plate)- and GLT (ribs)- members. The suggested elastic model is based on the work of Abdelouahed [13] and Smith and Teng [14] for the strengthening of concrete members with FRP plates and will be applied for the mentioned loadcarrying timber elements. As a result so far it could be observed, that high peaks of shear and tensile stresses perpendicular to the interface (glue-line) occur due to the elastic consideration of the material. The model was evaluated by some pre-test which showed an acceptable correlation between the predictions of the model and a 2D-FEM analysis. It is evident, that the notches at the end of the rips must be reinforced by e.g. self-tapping screws or glued in rod to achieve effective solutions for this load carrying element. With the discussed model the shear and tensile stresses and forces resp. perpendicular to the interface can be computed.
Online Access
Free
Resource Link
Less detail

Curved Cross Laminated Timber Elements

https://research.thinkwood.com/en/permalink/catalogue1545
Year of Publication
2016
Topic
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Author
Stecher, Georg
Maderebner, Roland
Zingerle, Philipp
Flach, Michael
Kraler, Anton
Year of Publication
2016
Country of Publication
Austria
Format
Conference Paper
Material
CLT (Cross-Laminated Timber)
Topic
Mechanical Properties
Keywords
Rolling Shear
Tensile Stress
Strength
Rigidity
Density
Language
English
Conference
World Conference on Timber Engineering
Research Status
Complete
Notes
August 22-25, 2016, Vienna, Austria p. 1131-1138
Summary
In timber construction, curved timber components have been used repeatedly. Yet the use of curved CLT elements is a relatively recent phenomenon. To obtain a European Technical Approval (ETA) for so-called radius timber (single curved CLT elements), Holzbau Unterrainer GmbH commissioned the accredited testing institution TVFA – Innsbruck to carry out the tests required for this purpose. To this end, overall 158 tests were performed in building component dimensions from December 2013 to May 2014, and several laboratory tests were carried out to monitor adhesive joint quality. Due to the single curved shape of radius timber elements, it is key to particularly focus on possible implications on load bearing capacity due to pre-stress of the slats and to the tensile stress perpendicular to grain resulting from deflection forces. To comply with the criteria laid down in the semi-probabilistic safety concept used in Eurocode 5, the impact caused by these pre-curvatures on strength, rigidity and gross density must be known.
Online Access
Free
Resource Link
Less detail

Cyclic Response of Insulated Steel Angle Brackets Used for Cross-Laminated Timber Connections

https://research.thinkwood.com/en/permalink/catalogue2765
Year of Publication
2021
Topic
Seismic
Acoustics and Vibration
Connections
Material
CLT (Cross-Laminated Timber)
Application
Walls
Floors
Author
Kržan, Meta
Azinovic, Boris
Publisher
Springer
Year of Publication
2021
Format
Journal Article
Material
CLT (Cross-Laminated Timber)
Application
Walls
Floors
Topic
Seismic
Acoustics and Vibration
Connections
Keywords
Angle Bracket
Sound Insulation
Insulation
Monotonic Test
Cyclic Tests
Wall-to-Floor
Stiffness
Load Bearing Capacity
Shear
Tensile
Language
English
Research Status
Complete
Series
European Journal of Wood and Wood Products
Summary
In cross-laminated timber (CLT) buildings, in order to reduce the disturbing transmission of sound over the flanking parts, special insulation layers are used between the CLT walls and slabs, together with insulated angle-bracket connections. However, the influence of such CLT connections and insulation layers on the seismic resistance of CLT structures has not yet been studied. In this paper, experimental investigation on CLT panels installed on insulation bedding and fastened to the CLT floor using an innovative, insulated, steel angle bracket, are presented. The novelty of the investigated angle-bracket connection is, in addition to the sound insulation, its resistance to both shear as well as uplift forces as it is intended to be used instead of traditional angle brackets and hold-down connections to simplify the construction. Therefore, monotonic and cyclic tests on the CLT wall-to-floor connections were performed in shear and tensile/compressive load direction. Specimens with and without insulation under the angle bracket and between the CLT panels were studied and compared. Tests of insulated specimens have proved that the insulation has a marginal influence on the load-bearing capacity; however, it significantly influences the stiffness characteristics. In general, the experiments have shown that the connection could also be used for seismic resistant CLT structures, although some minor improvements should be made.
Online Access
Free
Resource Link
Less detail

Effect of Array on Tensile Load Carrying Capacity CLT Drift Pinned Joint

https://research.thinkwood.com/en/permalink/catalogue1532
Year of Publication
2016
Topic
Connections
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Author
Nakashima, Shoichi
Kitamori, Akihisa
Araki, Yasuhiro
Isoda, Hiroshi
Year of Publication
2016
Country of Publication
Austria
Format
Conference Paper
Material
CLT (Cross-Laminated Timber)
Topic
Connections
Mechanical Properties
Keywords
Reduction Coefficients
Dowel-Type Connections
Drift Pinned Joint
Tensile Tests
Stiffness
Proportional Limit Load
Language
English
Conference
World Conference on Timber Engineering
Research Status
Complete
Notes
August 22-25, 2016, Vienna, Austria p. 772-779
Summary
A reduction coefficient is applied in usual design of multiple dowels type connections. The numbers of stiffeners in row is one of important factor to decide this coefficient. CLT drift pinned joint showed small orthotropy against in plane tensile load. Tensile tests of multiple drift pins joints were performed to evaluate the effect of array. Numbers of drift pins n in each specimen were same (n=12), but the arrangements were different (2 x 6, 3 x 4, 4 x 3, 6 x 2). Also the grain directions were parameters (0, 90 degrees). The reduction of initial stiffness and proportional limit load showed good agreement between theoretical prediction and experimental results.
Online Access
Free
Resource Link
Less detail

Effects of the Width and Lay-Up of Sugi Cross-Laminated Timber (CLT) on its Dynamic and Static Elastic Moduli, and Tensile Strength

https://research.thinkwood.com/en/permalink/catalogue521
Year of Publication
2016
Topic
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Author
Ido, Hirofumi
Nagao, Hirofumi
Harada, Masaki
Kato, Hideo
Ogiso, Junko
Miyatake, Atsushi
Publisher
Springer Japan
Year of Publication
2016
Country of Publication
Japan
Format
Journal Article
Material
CLT (Cross-Laminated Timber)
Topic
Mechanical Properties
Keywords
Modulus of Elasticity
Tensile Strength
Language
English
Research Status
Complete
Series
Journal of Wood Science
Summary
Cross-laminated timber (CLT) has recently emerged as a new wood product that utilizes a large quantity of domestic lumber. This study aims to analyze the effects of width and lay-ups on the tensile strength of CLT. To this end, the elastic modulus of sugi CLT with different lay-ups was measured by dynamic and static methods. Moreover, tensile tests were conducted for different widths and lay-ups of CLT. Results indicate that the apparent bending Young’s modulus, as calculated using the dynamic method, is directly proportional to the measured Young’s modulus in static method for each lay-up. Furthermore, there was no significant effect of width on the tensile strength in the range of 150, 300, and 600 mm. However, the variations in lay-ups affected the tensile strength as follows: CLT with larger ratio of the major strength direction lamina along the cross-section and with higher grade of lamina in the major strength direction showed higher tensile strength. The estimated tensile strength of CLT, as calculated using the Young’s modulus of the lamina of each layer, and the tensile strength of lamina as simple substance was found to be in good agreement with the measured tensile strength of CLT.
Online Access
Free
Resource Link
Less detail

Estimation of Strength Properties of Tensile Bolt Joint for CLT Construction

https://research.thinkwood.com/en/permalink/catalogue1859
Year of Publication
2016
Topic
Connections
Design and Systems
Material
CLT (Cross-Laminated Timber)
Application
Wood Building Systems
Author
Suzuki, Kei
Kobayashi, Kenji
Aoki, Kenji
Inayama, Masahiro
Tsuchimoto, Takahiro
Publisher
J-STAGE
Year of Publication
2016
Country of Publication
Japan
Format
Journal Article
Material
CLT (Cross-Laminated Timber)
Application
Wood Building Systems
Topic
Connections
Design and Systems
Keywords
Tensile Bolts
Strength Properties
Stiffness
Compression
Language
Japanese
Research Status
Complete
Series
Journal of Structural and Construction Engineering: Transactions of AIJ
Online Access
Free
Resource Link
Less detail

32 records – page 1 of 4.