For wood floor systems, their vibration performance is significantly dependent on the conditions of their supports, specifically the rigidity of the support. Detrimental effects could result if the floor supports do not have sufficient rigidity. This is special ture for floor supporting beams. The problem of vibrating floor due to flexible supporting beams can be solved through proper design of the supporting beams. However, there is currently no criterion set for the minimum requirement for floor supporting beam stiffness to ensure the beam is rigid enough. Designers’ current practice is to use the uniform load deflection criteria specified in the code for designing the supporting beams. This criterion is based on certain ratios of the floor span (e.g. L/360, L/480 etc.). The disadvantage of this approach is that it allows larger deflections for longer-span beams than for shorter beams. This means that engineers have to use their experience and judgement to select a proper ratio, particularly for the long-span beams. Therefore, a better vibration-controlled design criterion for supporting beams is needed.
It is recommended to further verify the ruggedness of the proposed stiffness criterion for floor supporting beams using new field supporting beam data whenever they become available.
In Phase I (2018-19) of this project on Prefabricated Heavy Timber Modular Construction, three major types of connections used in a stackable modular building were studied: intramodule connection, inter-module vertical connection, and inter-module horizontal connection. The load requirement and major design criteria were identified...
This project studied the feasibility and performance of a mass timber wall system based on Nail Laminated Timber (NLT) for floor/wall applications, in order to quantify the effects of various design parameters. Thirteen 2.4 m × 2.4 m shear walls were manufactured and tested in this phase. Together with another five specimens tested before, a total eighteen shear wall specimens and ten configurations were investigated. The design variables included fastener type, sheathing thickness, number of sheathings, sheathing material, nailing pattern, wall opening, and lumber orientation. The NLT walls were made of SprucePine-Fir (SPF) No. 2 2×4 (38 mm × 89 mm) lumber and Oriented Strand Lumber (OSB) or plywood sheathing. They were tested under monotonic and reverse-cyclic loading protocols, in accordance with ASTM E564-06 (2018) and ASTM E2126-19, respectively.
Compared to traditional wood stud walls, the best performing NLT based shear wall had 2.5 times the peak load and 2 times the stiffness at 0.5-1.5% drift, while retaining high ductility. The advantage of these NLT-based wall was even greater under reverse-cyclic loading due to the internal energy dissipation of NLT.
The wall with ring nails had higher stiffness than the one with smooth nails. But the performance of ring nails deteriorated drastically under reverse-cyclic loading, leading to a considerably lower capacity. Changing the sheathing thickness from 11 mm to 15 mm improved the strength by 6% while having the same initial stiffness. Adding one more face of sheathing increased the peak load and stiffness by at least 50%. The wall was also very ductile as the load dropped less than 10% when the lateral displacement exceeded 150 mm. The difference created by sheathing material was not significant if they were of the same thickness. Reducing the nailing spacing by half led to a 40% increasing in the peak load and stiffness. Having an opening of 25% of the area at the center, the lateral capacity and stiffness reached 75% or more of the full wall.
A simplified method to estimate the lateral resistance of this mass timber wall system was proposed. The estimate was close to the tested capacity and was on the conservative side. Recommendations for design and manufacturing the system were also presented.
Mass timber is a generic name for a broad range of thick and heavy wood products such as cross-laminated timber (CLT), dowel-laminated timber (DLT), nail-laminated timber (NLT), and gluelaminated timber (GLT), among others. So far, vibration-controlled design methods have been developed mostly for CLT floors.
La construction massive en bois est un terme générique qui englobe une grande variété de produits du bois épais et lourds, notamment le bois lamellé-croisé (CLT), le bois lamellé-goujonné (DLT), le bois lamellé-cloué et le bois lamellé-collé (GLT). À ce jour, les méthodes de conception à vibrations contrôlées ont surtout été élaborées pour les planchers en CLT.