The paper presents the design and detailing, and the experimental quasi-static 2/3 scale tests of two posttensioned wall systems: a single (more traditional) wall system (Figure 2) and a new configuration comprising of a column-wall-column coupled system (Figure 3). The latter allows avoiding displacement incompatibilities issues between the wall and the diaphragm by using the boundary columns as supports.
Three innovative massive wooden shear-wall systems (Cross-Laminated-Glued Wall, Cross-Laminated-Stapled Wall, Layered Wall with dovetail inserts) were tested and their structural behaviour under seismic action was assessed with numerical simulations. The wall specimens differ mainly in the method used to assemble the layers of timber boards composing them. Quasi-static cyclic loading tests were carried out and then reproduced with a non-linear numerical model calibrated on the test results to estimate the most appropriate behaviour factor for each system. Non-linear dynamic simulations of 15 artificially generated seismic shocks showed that these systems have good dissipative capacity when correctly designed and that they can be assigned to the medium ductility class of Eurocode 8. This work also shows the influence of deformations in wooden panels and base connectors on the behaviour factor and dissipative capacity of the system.
This paper summarises the experimental and numerical investigation conducted on the main connection of a novel steel-timber hybrid system called FFTT. The component behaviour of the hybrid system was investigated using quasi-static monotonic and reversed cyclic tests. Different steel profiles (wide flange I-sections and hollow rectangular sections) and embedment approaches for the steel profiles (partial and full embedment) were tested. The results demonstrated that when using an appropriate connection layout, the desired strong-column weak-beam failure mechanism was initiated and excessive wood crushing was avoided. A numerical model was developed that reasonably reflected the real component behaviour and can subsequently be used for numerical sensitivity studies and parameter optimization. The research presented herein serves as a precursor for providing design guidance for the FFTT system as an option for tall wood-hybrid buildings in seismic regions.
The research presented in this paper examines the performance of a shear connection using self-tapping screws (STS) in 3-ply Cross-Laminated Timber (CLT) panels. CLT panels were connected with STS assemblies at an inclined angle in two directions. The capacity of the STS assemblies was tested for the purpose of designing a CLT roof diaphragm of a large storage facility where a high-performance and low-manufacturing-cost solution was required. A total of eleven full-scale specimens were subjected to quasi-static and reversed-cyclic shear loading. Resulting forcedisplacement and hysteretic curves were used to determine an equivalent energy elastic-plastic curve based on ASTM E2126-11 procedures to estimate assembly yield strength, yield displacement, and ductility ratio. The performance in terms of strength and stiffness was excellent, and the STS provided the required ductility for the system to be used in seismic applications. Static yield strength averaged 80kN/m with an average ductility ratio of 7.7 while cyclic yield strength averaged 68kN/m with an average ductility ratio of 4.1. The data obtained allows engineers to specify low-cost lateral load resisting connection systems for large scale CLT structures.
In recent years, hybrid systems have grown in popularity as potential solution for mid-rise construction. There is also an increased interest in using timber for such systems. The lack of established design guidance, however, has tabled the practical implementation of timber-based hybrid structures. The aim of this thesis is to address the existing knowledge gap regarding the detailed connection design of hybrid systems through combined experimental and numerical investigations on a novel timber-steel system called “FFTT”. The FFTT system relies on wall panels of mass timber such as Cross-Laminated-Timber (CLT) for gravity and lateral load resistance and embedded steel beam sections to provide ductility under seismic loading. A vital step towards practical implementation of the FFTT system is to obtain the proof that the connections facilitate the desired ‘strong column – weak beam’ failure mechanism.
The numerical work applied the software ANSYS; a parametric study based on the results of previous tests was conducted to obtain a suitable connection configuration for improved structural performance. The experimental work, carried out at FPInnovations, consisted of quasi-static monotonic and reversed cyclic tests on two different connection configurations: fully and partially embedded ASTM wide flange sections in combination with 7 ply CLT panels. The combination of partial embedment length and full embedment depth, even when using the smallest wide flange section, did not facilitate the desired behavior. The connection performance was significantly improved when reducing the embedment depth (to avoid creating stress peaks on a weak cross layer) and increasing the embedment length (larger center to center distance between bearing plates). The used small size steel beam, however, is not practical for a real structure; therefore, further studies with larger beams and a modified geometry are recommended before the FFTT system can be applied in practice.
This article presents recent research on the seismic resistance of coupled post-tensioned timber walls for use in multi-story buildings. The walls are constructed from laminated veneer lumber (LVL), post-tensioned with unbonded vertical tendons, and coupled together with mild steel U-shaped flexural plates (UFPs) as energy dissipating elements. The timber wall design follows the same principles as used for post-tensioned precast concrete wall systems, using U-shaped plates to obtain a “hybrid” system, where energy is dissipated through yielding of the plates, while the vertical post-tensioning provides the restoring force. In this project, the same principles are applied to timber coupled walls. A series of quasi-static cyclic and pseudo-dynamic tests have been carried out to verify the applicability of the concept and the feasibility of the construction technology in timber buildings. The U-shaped plates showed stable energy dissipation characteristics and, in combination with the post-tensioning, desirable re-centering hysteretic behavior typically referred to as “flag-shape”. Because of the simplicity of these elements and the low cost of implementation, they have good prospects for practical application.
The work presented in this report is a continuation of the FPInnovations' research project on determining the performance of the CLT as a structural system under lateral loads. A two storey full-scale model of a CLT house was tested under quasi-static monotonic and cyclic lateral loading in two directions, one direction at a time. In total five tests were performed; one push-over and two cyclic tests were conducted in the longer symmetrical direction (E-W), and two cyclic tests were performed in the shorter asymmetrical direction (N-S). In addition, before and after each test, natural frequencies of the house in both directions were measured. The main objective of the tests was to investigate 3-D system behaviour of the CLT structure subjected to lateral loads. The CLT structure subjected to lateral loads performed according to the design objectives.
New Zealand Society for Earthquake Engineering Conference
March 21-23, 2014, Auckland, New Zealand
The paper presents the design and construction detailing of the quasi-static testing of two post-tensioned timber wall systems: a single (more traditional) wall system and a new configuration comprising of a column-wall-column coupled system (CWC). The latter allows avoiding displacement incompatibilities issues between the wall and the diaphragm by using the boundary columns as supports.
Different reinforcement configurations were taken into account for both the wall systems; the walls were subjected to different initial post-tensioning stress levels, and different dissipater options were considered: both internal and external replaceable mild steel tension-compression yield fuses, and U-shape Flexural Plates (UFPs) were used for the single wall and the CWC solutions respectively.
The experimental results showed the high-performance of both post-tensioned timber wall systems with negligible level of structural damage in the wall element and residual displacements and high level of dissipation.
This thesis discusses the results of experimental tests on two post-tensioned timber core-walls, tested under bi-directional quasi-static seismic loading. The half-scale two-storey test specimens included a stair with half-flight landings. Multi-storey timber structures are becoming increasingly desirable for architects and building owners due to their aesthetic and environmental benefits. In addition, there is increasing public pressure to have low damage structural systems with minimal business interruption after a moderate to severe seismic event. Timber has been used extensively for low-rise residential structures in the past, but has been utilised much less for multi-storey structures, traditionally limited to residential type building layouts which use light timber framing and include many walls to form a lateral load resisting system. This is undesirable for multi-storey commercial buildings which need large open spaces providing building owners with versatility in their desired floor plan. The use of Cross-Laminated Timber (CLT) panels for multi-storey timber buildings is gaining popularity throughout the world, especially for residential construction. Previous experimental testing has been done on the in-plane behaviour of single and coupled post-tensioned timber walls at the University of Canterbury and elsewhere. However, there has been very little research done on the 3D behaviour of timber walls that are orthogonal to each other and no research to date into post-tensioned CLT walls. The “high seismic option” consisted of full height post-tensioned CLT walls coupled with energy dissipating U-shaped Flexural Plates (UFPs) attached at the vertical joints between coupled wall panels and between wall panels and the steel corner columns. An alternative “low seismic option” consisted of post-tensioned CLT panels connected by screws, to provide a semi-rigid connection, allowing relative movement between the panels, producing some level of frictional energy dissipation.
New Zealand Society for Earthquake Engineering Conference
March 21-23, 2014, Auckland, New Zealand
This paper describes the results of experimental tests on two posttensioned timber core-walls tested under bi-directional quasi-static seismic loading. The half-scale two-storey test specimens included a stair with half-flight landings. The use of Cross-Laminated Timber (CLT) panels for multi-storey timber buildings is gaining popularity throughout the world, especially for residential construction. Posttensioned timber core-walls for lift-shafts or stairwells can be used for seismic resistance in open-plan commercial office buildings Previous experimental testing has been done on the in-plane behaviour of single and coupled timber walls at the University of Canterbury and elsewhere. However, there has been very little research done on the 3D behaviour of timber walls that are orthogonal to each other, and no research to date into post-tensioned CLT walls.
The “high seismic option” consisted of full height post-tensioned CLT walls coupled with energy dissipating U-shaped Flexural Plates (UFPs) attached at the vertical joints between coupled wall panels and between wall panels and the steel corner columns. An alternative “low seismic option” consisted of post-tensioned CLT panels connected by screws, to provide a semi-rigid connection, allowing relative movement between the panels, producing some level of frictional energy dissipation.