The research presented in this paper examines the shear resistance performance of self-tapping screws (STS) in three-ply cross-laminated timber (CLT) panels. Specifically, the feasibility of using innovative STS assemblies with double inclination of fasteners was investigated for the shear connection of CLT panels. The specimens (1.5×1.5 m) were subjected to quasi-static and reversed-cyclic loading. The tests were set up to approximate pure shear loading, with three-panel CLT assemblies connected with STS. The resulting load-displacement and hysteretic curves were used to determine an equivalent energy elastic-plastic curve to estimate assembly capacity, yield load, yield displacement, ductility ratio, stiffness, and damping. Excellent structural performance in terms of capacity and stiffness was obtained while still providing the required ductility for the system to be used in seismic applications. The average static and cyclic yield loads were 6.0 kN/screw and 5.9 kN/screw, respectively. Average static and cyclic and ductility ratios were 7.7 and 4.1, respectively, allowing the connection to be classified as highly ductile under quasi-static loading and moderately ductile under reversed cyclic loading. The data obtained allow engineers to specify an innovative connection assembly with double inclination of fasteners for lateral load–resisting systems of CLT structures.
This paper summarises the experimental and numerical investigation conducted on the main connection of a novel steel-timber hybrid system called FFTT. The component behaviour of the hybrid system was investigated using quasi-static monotonic and reversed cyclic tests. Different steel profiles (wide flange I-sections and hollow rectangular sections) and embedment approaches for the steel profiles (partial and full embedment) were tested. The results demonstrated that when using an appropriate connection layout, the desired strong-column weak-beam failure mechanism was initiated and excessive wood crushing was avoided. A numerical model was developed that reasonably reflected the real component behaviour and can subsequently be used for numerical sensitivity studies and parameter optimization. The research presented herein serves as a precursor for providing design guidance for the FFTT system as an option for tall wood-hybrid buildings in seismic regions.
The structural use of wood in North America is dominated by light wood-frame construction used in low-rise and – more recently – mid-rise residential buildings. Mass timber engineered wood products such as laminatedveneer-lumber and cross-laminated timber (CLT) panels enable to use the material in tall and large wood and woodbased hybrid buildings. The prospect of constructing taller buildings creates challenges, one of them being the increasein lateral forces created by winds and earthquakes, thus requiring stronger hold-down devices. This paper summarises the experimental investigation on the performance a high-capacity hold-down for resisting seismic loads in tall timberbased structural systems. The connection consists of the Holz-Stahl-Komposit-System (HSK)™ glued into CLT with the modification that ductile steel yielding was allowed to occur inside the CLT panel. The strength, stiffness, ductility and failure mechanisms of this connection were evaluated under quasi-static monotonic and reversed cyclic loading. The results demonstrate that the modified hold-down-assembly provides a possible solution for use in tall timber-based structures in high seismic zones
The research presented in this paper examines the performance of a shear connection using self-tapping screws (STS) in 3-ply Cross-Laminated Timber (CLT) panels. CLT panels were connected with STS assemblies at an inclined angle in two directions. The capacity of the STS assemblies was tested for the purpose of designing a CLT roof diaphragm of a large storage facility where a high-performance and low-manufacturing-cost solution was required. A total of eleven full-scale specimens were subjected to quasi-static and reversed-cyclic shear loading. Resulting forcedisplacement and hysteretic curves were used to determine an equivalent energy elastic-plastic curve based on ASTM E2126-11 procedures to estimate assembly yield strength, yield displacement, and ductility ratio. The performance in terms of strength and stiffness was excellent, and the STS provided the required ductility for the system to be used in seismic applications. Static yield strength averaged 80kN/m with an average ductility ratio of 7.7 while cyclic yield strength averaged 68kN/m with an average ductility ratio of 4.1. The data obtained allows engineers to specify low-cost lateral load resisting connection systems for large scale CLT structures.
Timber-Concrete Composite (TCC) systems are comprised of a timber element connected to a concrete slab through a mechanical shear connection. A large number of T-beam configurations currently exist; however, the growing availability of panel-type engineered wood products (EWPs) in North America in combination with a concrete topping has offered designers and engineers greater versatility in terms of architectural expression and structural and building physics performance. The focus of this investigation was to experimentally determine the properties for a range of TCC systems in several EWPs. Strength and stiffness properties were determined for different TCC configurations based on small-scale shear tests. Eighteen floor panels were tested for elastic stiffness under a quasi-static loading protocol and measurements of the dynamic properties were obtained prior to loading to failure. The tests confirmed that calculations according to the -method can predict the basic stiffness and dynamic properties of TCC floors within a reasonable degree of accuracy. Floor capacities were more difficult to predict, however, failure occurred at loads that were between four and ten times serviceability requirements. The research demonstrated that all selected connector configurations produced efficient timber-concrete-composite systems.
Recent developments in novel engineered mass timber products and connection systems have created the possibility to design and construct tall timber-based buildings. This research presents the experiments conducted on the steel-wood connection as main energy dissipating part of a novel steel–timber hybrid system labelled Finding the Forest Through the Trees (FFTT). The performance was investigated using quasi-static monotonic and reversed cyclic tests. The influence of different steel beam profiles (wide flange I-sections and hollow rectangular sections), and the embedment approaches (partial and full embedment) was investigated. The test results demonstrated that appropriate connection layouts can lead to the desired failure mechanism while avoiding excessive crushing of the mass timber panels. The research can serve as a precursos for developing design guidelines for the FFTT systems as an option for tall wood-hybrid building systems in seismic regions.
Cross-Laminated-Timber (CLT) is increasingly gaining popularity in residential and non-residential applications in North America. To use CLT as lateral load resisting system, individual panels need to be connected. In order to provide in-plane shear connections, CLT panels may be joined with a variety of options including the use of self-tapping-screws (STS) in surface splines and half-lap joints. Alternatively, STS can be installed at an angle to the plane allowing for simple butt joints and avoiding any machining. This study investigated the performance of CLT panel assemblies connected with STS under vertical shear loading. The three aforementioned options were applied to join 3ply and 5-ply CLT panels. A total of 60 mid-scale quasi-static shear tests were performed to determine and compare the connection performance in terms of strength, stiffness, and ductility. It was shown that – depending on the screw layout – either very stiff or very ductile joint performance can be achieved.
The research presented in this paper examines the performance of 3-ply and 5-ply Cross-laminated Timber (CLT) panels connected with Self-tapping Screws (STS). Different conventional joint types (surface spline with STS in shear and half-lap joints with STS in either shear or withdrawal) along with two innovative solutions were evaluated in a total of 198 quasi-static tests. The first novel assembly used STS with double inclination of fasteners in butt joints; the second was a combination of STS in withdrawal and shear in lap joints. The joint performance was evaluated in terms of capacity, stiffness, yield strength, and ductility. The results confirmed that joints with STS in shear exhibited high ductility but low stiffness, whereas joints with STS in withdrawal were found to be stiff but less ductile. Combining the shear and withdrawal action of STS led to high stiffness and high ductility.