The structural use of wood in North America is dominated by light wood-frame construction used in low-rise and – more recently – mid-rise residential buildings. Mass timber engineered wood products such as laminatedveneer-lumber and cross-laminated timber (CLT) panels enable to use the material in tall and large wood and woodbased hybrid buildings. The prospect of constructing taller buildings creates challenges, one of them being the increasein lateral forces created by winds and earthquakes, thus requiring stronger hold-down devices. This paper summarises the experimental investigation on the performance a high-capacity hold-down for resisting seismic loads in tall timberbased structural systems. The connection consists of the Holz-Stahl-Komposit-System (HSK)™ glued into CLT with the modification that ductile steel yielding was allowed to occur inside the CLT panel. The strength, stiffness, ductility and failure mechanisms of this connection were evaluated under quasi-static monotonic and reversed cyclic loading. The results demonstrate that the modified hold-down-assembly provides a possible solution for use in tall timber-based structures in high seismic zones
Timber-Concrete Composite (TCC) systems are comprised of a timber element connected to a concrete slab through a mechanical shear connection. A large number of T-beam configurations currently exist; however, the growing availability of panel-type engineered wood products (EWPs) in North America in combination with a concrete topping has offered designers and engineers greater versatility in terms of architectural expression and structural and building physics performance. The focus of this investigation was to experimentally determine the properties for a range of TCC systems in several EWPs. Strength and stiffness properties were determined for different TCC configurations based on small-scale shear tests. Eighteen floor panels were tested for elastic stiffness under a quasi-static loading protocol and measurements of the dynamic properties were obtained prior to loading to failure. The tests confirmed that calculations according to the -method can predict the basic stiffness and dynamic properties of TCC floors within a reasonable degree of accuracy. Floor capacities were more difficult to predict, however, failure occurred at loads that were between four and ten times serviceability requirements. The research demonstrated that all selected connector configurations produced efficient timber-concrete-composite systems.
Cross-Laminated-Timber (CLT) is increasingly gaining popularity in residential and non-residential applications in North America. To use CLT as lateral load resisting system, individual panels need to be connected. In order to provide in-plane shear connections, CLT panels may be joined with a variety of options including the use of self-tapping-screws (STS) in surface splines and half-lap joints. Alternatively, STS can be installed at an angle to the plane allowing for simple butt joints and avoiding any machining. This study investigated the performance of CLT panel assemblies connected with STS under vertical shear loading. The three aforementioned options were applied to join 3ply and 5-ply CLT panels. A total of 60 mid-scale quasi-static shear tests were performed to determine and compare the connection performance in terms of strength, stiffness, and ductility. It was shown that – depending on the screw layout – either very stiff or very ductile joint performance can be achieved.
The research presented in this paper examines the performance of 3-ply and 5-ply Cross-laminated Timber (CLT) panels connected with Self-tapping Screws (STS). Different conventional joint types (surface spline with STS in shear and half-lap joints with STS in either shear or withdrawal) along with two innovative solutions were evaluated in a total of 198 quasi-static tests. The first novel assembly used STS with double inclination of fasteners in butt joints; the second was a combination of STS in withdrawal and shear in lap joints. The joint performance was evaluated in terms of capacity, stiffness, yield strength, and ductility. The results confirmed that joints with STS in shear exhibited high ductility but low stiffness, whereas joints with STS in withdrawal were found to be stiff but less ductile. Combining the shear and withdrawal action of STS led to high stiffness and high ductility.
Nail-laminated timber-concrete composite (TCC) is a system composed of a nail-laminated timber (NLT) panel connected to a concrete slab through shear connections. When used as flexural elements such as floors, the concrete and NLT are located in the compression and tension zones, respectively...
In the US, codified seismic design procedure requires the use of seismic performance factors which are currently not available for CLT shear wall systems. The study presented herein focuses on the determination of seismic design factors for CLT shear walls in platform type construction using the FEMA P-695 process. Results from the study will be proposed for implementation in the seismic design codes in the US. The project approach is outlined and selected results of full-scale shear wall testing are presented and discussed. Archetype development, which is required as part of the FEMA P-695 process, is briefly explained with an example. Quasi-static cyclic tests were conducted on CLT shear walls to systematically investigate the effects of various parameters. The key aspect of these tests is that they systematically investigate each potential modelling attribute that is judged within the FEMA P-695 uncertainty quantification process. Boundary constraints and gravity loading were both found to have a beneficial effect on the wall performance, i.e. higher strength and deformation capacity. Higher aspect ratio panels (4:1) demonstrated lower stiffness and substantially larger deformation capacity compared to moderate aspect ratio panels (2:1). However, based on the test results there is likely a lower bound for aspect ratio (at 2:1) where it ceases to benefit deformation capacity of the wall. This is due to the transition of the wall behaviour from rocking to sliding. Phenomenological models were used in modelling CLT shear walls. Archetype selection and analysis procedure was demonstrated and nonlinear time history analysis was conducted using different wall configurations.