The glulam is determined by, and therefore a representation of, a new kind of ecological structural materials. The aim of this study was to summarize the mechanical performance especially the flexural behavior of various kinds of glulam and the physical properties of their relevant original timbers including pseudotsuga menziesii, larch, Yi poplar, poplar, China fir, mongolian scotch pine and camphor. And then it established and analyzed the relationship between the two to contrast those timber species so as to provide engineers with some reference in selecting timber glulam.
To explore the feasibility of hem-fir for CLT products, this work addressed the exploratory
and pilot plant studies of hem-fir cross-laminated timber (CLT) products through mechanical
tests. The hem-fir lumber was procured and then stress-graded based on dynamic modulus of
elasticity (MOE). The resulted 5-ply prototype CLT products were then tested non-destructively
and 3-ply pilot plant hem-fir CLT was tested destructively. The results showed that bending
performance of hem-fir CLT panel can be predicted. Considering cost-competitiveness and
end applications of hem-fir CLT products, the panel structure can be optimized based on the
stress-graded data of hem-fir lumber.
This study aimed to investigate the durability of structural laminated veneer lumber (LVL) during outdoor use. We subjected LVL to outdoor exposure tests for 48 months; the tests were designed under the assumption of outdoor use such as temporary enclosure plates used in the construction field. The surfaces of the LVL specimens were painted, or preservatives were mixed with the adhesive in the glue line. Very slight changes were observed in the color of the specimens painted with solvent-born coatings. Modulus of rupture (MOR) in the flatwise direction after 48 months exposure was deteriorated to 60–80% of the initial value. The MOR in the edgewise direction was higher than that in the flatwise direction. The MOR values of the painted specimens were higher than those of the control specimens before 24 months of outdoor exposure, whereas after 36 months of exposure, the values of the painted specimens were almost equal to those of the control specimens. Shear strength retention was greater than MOR retention. We found that the face veneers of the specimens were deteriorated by outdoor exposure, whereas their inner layers were relatively sound.
Solid-sawn lumber (Douglas-fir, southern pine, Spruce– Pine–Fir, and yellow-poplar), laminated veneer lumber (Douglas-fir, southern pine, and yellow-poplar), and laminated strand lumber (aspen and yellow-poplar) were heated continuously at 82°C (180°F) and 80% relative humidity (RH) for periods of up to 24 months. The lumber was then reconditioned to room temperature at 20% RH and tested in edgewise bending. Little reduction occurred in modulus of elasticity (MOE) of solid-sawn lumber, but MOE of composite lumber products was somewhat reduced. Modulus of rupture (MOR) of solid-sawn lumber was reduced by up to 50% after 24 months exposure. Reductions in MOR of up to 61% were found for laminated veneer lumber and laminated strand lumber after 12 months exposure. A limited scope study indicated that the results for laminated veneer lumber in edgewise bending are also applicable to flatwise bending. Comparison with previous results at 82°C (180°F)/25% RH and at 66°C (150°F)/20% RH indicate that differences in the permanent effect of temperature on MOR between species of solid-sawn lumber and between solid-sawn lumber and composite lumber products are greater at high humidity levels than at low humidity levels. This report also describes the experimental design of a program to evaluate the permanent effect of temperature on flexural properties of structural lumber, with reference to previous publications on the immediate effect of temperature and the effect of moisture content on lumber properties.
The cross-laminated timber (CLT) technology is also perceived as a potential for utilization of lumber oflower grades and underused species, because the core layers perpendicular to the principle loading direction transferloads through rolling shear, which is not correlated to the grade of lumber. Current the product standard however specifies the minimum grade requirements for all lumber to be used as CLT laminations. In this study the effect of the presence of knots in the transverse core layer of CLT billets was examined in matched CLT samples where the heavy presence of knots in the transverse core layer was the only variable compared to knot free reference. All samples were tested as short-beams in three point bending and all failed in rolling shear in the transverse core layer. The presence of knots had no measurable effect on the shear capacity expressed as nominal MOR of the tested CLT beam samples
The effects of veneer orientation and loading direction on the mechanical properties of bamboo-bundle/poplar veneer laminated veneer lumber (BWLVL) were investigated by a statistical analysis method. Eight types of laminated structure were designed for the BWLVL aiming to explore the feasibility of manufacturing high-performance bamboo-based composites. A specific type of bamboo species named Cizhu bamboo (Neosinocalamus affinis) with a thickness of 6 mm and diameter of 65 mm was used. The wood veneers were from fast-growing poplar tree (Populus ussuriensis Kom.) in China. The bamboo bundles were obtained by a mechanical process. They were then formed into uniform veneers using a onepiece veneer technology. Bamboo bundle and poplar veneer were immersed in water-soluble phenol formaldehyde (PF) resin with low molecular weight for 7 min and dried to MC of 8–12 % under the ambient environment. All specimens were prepared through hand lay-up using compressing molding method. The density and mechanical properties including modulus of elasticity (MOE), modulus of rupture (MOR), and shearing strength (SS) of samples were characterized under loading parallel and perpendicular to the glue line. The results indicated that as the contribution of bamboo bundle increased in laminated structure, especially laminated on the surface layers, the MOE, MOR and SS increased. A lay-up BBPBPBB (Bbamboo, P-poplar) had the highest properties due to the cooperation of bamboo bundle and poplar veneer. A higher value of MOE and MOR was found for the perpendicular loading test than that for the parallel test, while a slightly higher SS was observed parallel to the glue line compared with perpendicular loading. Any lay-up within the homogeneous group can be used to replace others for obtaining the same mechanical properties in applications. These findings suggested that the laminated structure with high stiffness laid-up on the surface layers could improve the performance of natural fiber reinforced composites.
In order to improve the bending strength performance of three-ply laminated wood panels and use them as construction-grade panel materials, twelve types of three-ply cross-laminated wood panels whose percentages of core lamina thickness versus total lamina thickness were 33%, 50%, and 80% were made with sugi (Japanese cedar), and the effect of component ratio of the face and core laminae on their static bending strength performance was investigated.
The moduli of elasticity (MOE), proportional limit stresses and moduli of rupture (MOR), perpendicular (C type) and parallel (C type) to the grain of face laminae markedly increased or decreased with increasing percentage of core lamina thickness. The percentages of core lamina thickness at which each strength property value of C type became equal to that of C type ranged from 65% to 80%. At each percentage of core lamina thickness, the MOE and proportional limit stress of C type were higher in C (45) specimens having perpendicular-direction lamina of 45° annual ring angle in the core than in C (90) specimens having perpendicular-direction lamina of 90° in the core, whereas there was little difference in MOR between C (45) specimens and C (90) specimens. For 45° specimens having the core lamina thickness from 60% to 70%, MOE as well as MOR parallel and perpendicular to the grain of face laminae exceeded the corresponding requirement values of structural plywood with 21.0-mm thickness specified in Japanese Agricultural Standards.