Timber provides attractive earthquake performance characteristics for regions of high seismic risk, particularly its high strength-to-weight ratio; however, current timber structural systems are associated with relatively low design force reduction factors due to their low inherent ductility when compared to high-performance concrete and steel...
Key point to development of environmentally friendly timber structures, appropriate to urban ways of living, is the development of high-rise timber buildings. Comfort properties are nowadays one of the main limitations to tall timber buildings, and an enhanced knowledge on damping phenomena is therefore required, as well as improved prediction models for damping.
The aim of this work has consequently been to estimate various damping quantities in timber structures. In particular, models have been derived for predicting material damping in timber members, beams or panels, or in more complex timber structures, such as floors. Material damping is defined as damping due to intrinsic material properties, and used to be referred to as internal friction. In addition, structural damping, defined as damping due to connections and friction in-between members, has been estimated for timber floors.
The following paper describes the first stage of dynamic testing of a post-tensioned timber building to be performed in the structural laboratory of the University of Basilicata in Potenza, Italy as part of a series of experimental tests in collaboration with the University of Canterbury in Christchurch, New Zealand. During this stage of testing a 3-dimensional, 3-storey post-tensioned timber structure will be tested. The specimen is 2/3rd scale and made up of frames in both directions composed of post-tensioned timber. The specimen will be tested both with and without the addition of dissipative steel angles which are designed to yield at a certain level drift. These steel angles release energy through hysteresis during movement thus increasing damping. The following paper discusses the testing set-up and preliminary numerical predictions of the system performance. Focus will be placed on damping ratios, displacements and accelerations.
Ninth European Conference on Noise Control (Euronoise)
June 10-13, 2012, Prague, Czech Republic
In residential multi-storey buildings of timber it is of great importance to reduce the flanking transmission of noise. Some building systems do this by installing a vibration-damping elastic interlayer, Sylomer or Sylodyn , in the junction between the support and the floor structure. This interlayer also improves the floor vibration performance by adding damping to the structure. In the present work the vibration performance of a floor with such interlayers has been investigated both in laboratory and field tests. A prefabricated timber floor element was tested in laboratory on rigid supports and on supports with four different types of interlayers. The results are compared with in situ tests on a copy of the same floor element. The effect on vibration performance i.e. frequencies, damping ratio and mode shapes is studied. A comparison of the in situ test and the test with elastic interlayer in laboratory shows that the damping in situ is approximately three times higher than on a single floor element in the lab. This indicates that the damping in situ is affected be the surrounding building structure. The achieved damping ratio is highly dependent on the mode shapes. Mode shapes that have high mode shape coefficients along the edges where the interlayer material is located, result in higher modal damping ratios. The impulse velocity response, that is used to evaluate the vibration performance and rate experienced annoyance in the design of wooden joist floors, seems to be reduced when adding elastic layers at the supports.
Understanding the inherent damping mechanisms of floor vibrations has become a matter of increasing importance following the development of new composite floor layouts and increased span. The present study focuses on the evaluation of material damping in timber beam specimens with dimensions that are typical of common timber floor structures. Using the impact test method, 11 solid wood beams and 11 glulam beams made out of Norway Spruce (Picea abies) were subjected to flexural vibrations. The tests involved different spans and orientations. A total of 420 material damping evaluations were performed, and the results are presented as mean values for each configuration along with important statistical indicators to quantify their reliability. The consistency of the experimental method was validated with respect to repeatability and reproducibility. General trends found an increasing damping ratio for higher modes, shorter spans, and edgewise orientations. It is concluded from the results that material damping of timber beams of structural dimensions is governed by shear deformation, which can be expressed more conveniently with respect to the specific mode shape and its derivatives.
March 29-31, 2012, Chicago, Illinois, United States
This paper describes initial experimental testing to investigate feasible sources of passive damping for the seismic design of post-tensioned glue laminated timber structures. These innovative high performance structural systems extend precast concrete PRESSS technology to engineered wood structures, combining the use of post-tensioning bars or cables with large post-tensioned timber members. The combination of these two elements provides elastic recentering to the structure while the addition of damping using a specialised energy dissipation system gives the desirable `flag shaped' hysteretic response under lateral loading. Testing has been performed on a full scale beam-column joint at the University of Basilicata in Italy in a collaborative project with the University of Canterbury, New Zealand. The experimental testing uses engineered wood products, extending the use of laminated veneer lumber (LVL) structures tested in New Zealand to testing of glue laminated timber (glulam) structures in Italy. Current testing is aimed at further improvement of the system through additional energy dissipation systems.
This report summarizes the results of our ground motion evaluation for the proposed FRMWRK Office building to be constructed at 430 NW 10th Avenue in Portland, Oregon. Our geotechnical report for the project was submitted on November 30, 2015 (GeoDesign, 2015). The site is shown relative to surrounding features on Figure 1...
Glued laminated timber Tudor arches have been in wide use in the United States since the 1930s, but detailed knowledge related to seismic design in modern U.S. building codes is lacking. FEMA P-695 (P-695) is a methodology to determine seismic performance factors for a seismic force resisting system. A limited P-695 study for...