A major problem in light-weight timber floors is their insufficient performance coping with impact noise in low frequencies. There are no prefabricated solutions available in Australia and New Zealand. To rectify this and enable the implementation of lig...
Using Charles and Ray Eames’s famous 1950s House of Cards slotting toy as both design metaphor and structural precedent provides the starting point for a novel building logic (utilising three existing Swedish timber systems) that allows volumetrically slotted units to stack inside of and support each other. Contemporary computer-aided fabrication techniques based on evolutionary algorithms and CNC manufacturing strategies are used to produce a methodology for designing a kit-of-parts system at the scale of the skyscraper, based on the slotting together of cross-laminated timber (CLT) panels. A catalogue of novel slotting methods is produced, and a number of alternative slotted joint treatments identified that hold promising potential for further development, parametrically design and control volumes, understand the fabrication workflow and constructional sequence on site, and build prototypes of the chosen slotting configurations at scales ranging between 1:50 and 1:1.
The ambient movement of three modern multi-storey timber buildings has been measured and used to determine modal properties. This information, obtained by a simple, unobtrusive series of tests, can give insights into the structural performance of these forms of building, as well as providing information for the design of future, taller timber buildings for dynamic loads. For two of the buildings, the natural frequency has been related to the lateral stiffness of the structure, and compared with that given by a simple calculation. In future tall timber buildings, a new design criterion is expected to become important: deflection and vibration serviceability under wind load. For multi-storey timber buildings there is currently no empirical basis to estimate damping for calculation of wind-induced vibration, and there is little information for stiffness under wind load. This study therefore presents a method to address those gaps in knowledge.
The paper deals with a numerical analysis of timber-concrete ceiling. The finite element method is used for the analysis. The calculation takes into account a dynamic effect of load. The structure creates the ceiling of the gymnasium. The goal of the paper is a study of ceiling eigenfrequencies and a maximum response to a harmonic excitation...
There is a need of more advanced analysis for studying how the long-term behaviour of glued laminated timber structures is affected by creep and by cyclic variations in climate. A beam theory is presented able to simulate the overall hygro-mechanical and visco-elastic behaviour of (inhomogeneous) glulam structures. Two frame structures subjected to both mechanical and cyclic environmental loading are analysed to illustrate the advantages the model involved can provide. The results indicate clearly both the (discontinuous) inhomogeneity of the glulam products and the variable moisture-load action that occurs to have a significant effect on deformations, section forces and stress distributions within the frame structures that were studied
In a current research project the gluability of various soft- und hardwood species and their applicability in glued laminated timber are investigated. The influence of the processing parameters on the delamination resistance and shear strength of the glue lines are presented in this work.
The bonding forces, which are necessary for the integrity of a glue line, act in the interface within a distance that varies from nanometers to micrometers. The parameters that may have significant influence on the bonding strength and durability of adhesive joints are numerous and depend on the type of wood, adhesive and processing conditions.
This report begins with a discussion of the mechanisms of flame spread over combustible materials while describing the NBCC prescriptive solutions that establish the acceptable fire performance of interior finish materials. It is noted that while flame spread ratings do give an indication of the fire performance of products in building fires, the data generated are not useful as input to fire models that predict fire growth in buildings.
The cone calorimeter test is then described in some detail. Basic data generated in the cone calorimeter on the time to ignition and heat release rates are shown to be fundamental properties of wood products which can be useful as input to fire models for predicting fire growth in buildings.
The report concludes with the recommendation that it would be useful to run an extensive set of cone calorimeter tests on SCL, glue-laminated timber and CLT products. The fundamental data could be most useful for validating models for predicting flame spread ratings of massive timber products and useful as input to comprehensive computer fire models that predict the course of fire in buildings. It is also argued that the cone calorimeter would be a useful tool in assessing fire performance during product development and for quality control purposes.
Vibrations induced by people walking is one of the most important issue in timber floor design. Low natural frequency and low mass require a careful analysis in order to prevent significant annoyance and to guarantee an acceptable human comfort. This paper is concerned with the assessment of vibration performance of a timber-concrete composite timber floor and a cross laminated timber floor used in two timber buildings under construction in Trento (Italy). Different approaches suggested by Standards and literature were employed: analytical methods, numerical analyses and laboratory tests. About analytical methods the uniformed distributed load deflection criterion (ULD), the Eurocode 5 criterion and some criterions from literature were compared, whereas the Vibration Dose Value (VDV) method, as suggested by ISO 10137, was used for the numerical models and the laboratory tests. The numerical analyses were carried out by means of a finite element modelling. The load due to footfall was simulated by static and dynamic vertical forces. The laboratory tests were characterized by thirty walking tests for each floor. Impact testing with modal hammer was also undertaken in order to investigate the dynamic properties of the specimens. All results are compared and discussed.