Timber provides attractive earthquake performance characteristics for regions of high seismic risk, particularly its high strength-to-weight ratio; however, current timber structural systems are associated with relatively low design force reduction factors due to their low inherent ductility when compared to high-performance concrete and steel...
There is a need of more advanced analysis for studying how the long-term behaviour of glued laminated timber structures is affected by creep and by cyclic variations in climate. A beam theory is presented able to simulate the overall hygro-mechanical and visco-elastic behaviour of (inhomogeneous) glulam structures. Two frame structures subjected to both mechanical and cyclic environmental loading are analysed to illustrate the advantages the model involved can provide. The results indicate clearly both the (discontinuous) inhomogeneity of the glulam products and the variable moisture-load action that occurs to have a significant effect on deformations, section forces and stress distributions within the frame structures that were studied
Recent years have seen more architects and clients asking for tall timber buildings. In response, an ambitious timber community has been proposing challenging plans and ideas for multi-storey commercial and residential timber buildings. While engineers have been intensively looking at gravity-load-carrying elements as well as walls, frames and cores to resist lateral loads, floor diaphragms have been largely neglected.
Complex floor geometries and long span floor diaphragms create stress concentrations, high force demand and potentially large deformations. There is a lack of guidance and regulation regarding the analysis and design of timber diaphragms so structural engineers need a practical alternative to simplistic equivalent deep beam analysis or costly finite element modelling.
This paper proposes an equivalent truss method capable of solving complex geometries for both light timber framing and massive timber diaphragms. Floor panels are discretized by equivalent diagonals, having the same stiffness as the panel including its fasteners. With this method the panel unit shear forces (shear flow) and therefore fastener demand, chord forces and reaction forces can be evaluated. Because panel stiffness is accounted for, diaphragm deflection, torsional effects and transfer forces can also be assessed.
The fracture characteristics and deformation ability in timber engineering is very important criteria for structural design. However those fracture patterns are complex and confusing, so the quantitative evaluation is very difficult. In our past study, we could see the three fracture types and defined them the brittle, ductile and inter-mediate type with bolted connections loaded perpendicular to the grain. This definition isn’t enough because it’s not clear definition and we couldn’t study the deformation ability or ductility factor.In this study, for those connections, we would apply the evaluation method proposed by Ian et al. In this evaluation method, fracture pattern would have relevance to ductility factor. And the evaluation methods proposed by us, AIJ code and Ian et al would be compared. As a result, it is confirmed that fracture pattern based on mechanical calculation proposed by Ian could be agree with the pattern based on our video observation. Then proposed method would be useful for structural design.
Hybrid composite glulam timber reinforced using deformed steel bars and epoxy resin adhesive (RGTSB), was significantly developed in Kagoshima University. In this paper, a beam-to-beam connection for RGTSB and experimental data on the connection are presented. Two 2:3-scaled simply-supported beams under four-point flexural bending in short-term loading, connection elements under short and long-term tension loading were tested. The connection for RGTSB beam performed on bending behaviour such as non-connection RGTSB beam, especially better on ductility.
Hybrid composite glulam timber reinforced using deformed steel bars and epoxy resin adhesive (RGTSB), was significantly developed in Kagoshima University. A long term laboratory investigation on a 4.5-meter-span hybrid timber beam and a non-hybrid timber beam was started from August 2011. The beam was made of RGTSB and another was of conventional glulam timber...
In this paper, bending behaviours in hybrid composite glulam timbers reinforced using deformed steel bars and epoxy resin adhesives (RGTSB) are presented. The technique RGTSB was developed in order to improve flexural stiffness and strength in glulam timbers...
In a current research project the gluability of various soft- und hardwood species and their applicability in glued laminated timber are investigated. The influence of the processing parameters on the delamination resistance and shear strength of the glue lines are presented in this work.
The bonding forces, which are necessary for the integrity of a glue line, act in the interface within a distance that varies from nanometers to micrometers. The parameters that may have significant influence on the bonding strength and durability of adhesive joints are numerous and depend on the type of wood, adhesive and processing conditions.