Properties of CLT panels are influenced by the properties of their layers and the layer properties are in turn influenced by the structural characteristics of the laminate material. In order to realize the mechanical property potential of CLT panels it is necessary to understand the effects of laminate properties on the performance of the final product. This paper presents the approach and outcomes of an on-going study dealing with the evaluation of material and structural characteristics of laminates and their effects on overall characteristics of CLT using modal testing. Characteristics of “homogenised” layers and CLT panels were evaluated using modal and static testing. The suitability of test methods was established for single-layer panels and CLT panels. Relationships between overall single-layer properties and laminate characteristics were established. Differences in CLT properties calculated by different calculation models were discussed.
Wood-concrete composite slab floors provide a promising solution for achieving long spans and shallow wood-based floor systems for large and tall wood buildings. In comparison with conventional wood floor systems, such long span and heavy floors have a lower fundamental natural frequency, which challenges the floor vibration controlled design. A laboratory study, including subjective evaluation and measurement of the natural frequencies and one-kN static deflections, was conducted on wood-concrete composite floors. Method of calculation of the composite bending stiffness of the wood-concrete composite floor is proposed. The design criterion for human comfort was derived from the subjective evaluation results using the calculated fundamental natural frequency and 1 kN static deflection of one meter wide strip of the composite floor. The equation to directly determine the vibration controlled spans from the stiffness and mass was derived. Limited verification was performed. Further verification is needed when more field wood-concrete composite floors become available.
This study focuses on the vibrational behaviour of 3, 5 and 7-layer cross-laminated timber (CLT) plates supported on two sides with different support conditions. Three end support setups are proposed; 1) top load over the two supported edges, 2) direct fastening to support using self-tapping screws, 3) steel angle bracket support. The measured response parameters are natural frequencies, damping, and static deflection under a point load. The rotational stiffness with load, screws and steel angle brackets will be characterized through static tests. In addition, the effect of the span is studied by varying the test span and repeating the vibration and deflection tests. The laboratory tests will be supplemented with analytical modelling. The expected outcome is the development of approaches to more accurately calculate the natural frequency and static deflection under a point load, which can account for the influence of common support conditions encountered in service.
The design and application of cross laminated timber (CLT) is s trongly influenced by rolling shear properties of cross layers. Hence, predicting the mechanical behaviour of CLT requires accurate information about its rolling shear properties. In this study, black spruce wood laminates with three different growth ring orientations (flat sawn, in-between, quarter sawn) were edge glued to produce wooden cross layer (WCL). Two-plate shear tests were carried out on WCL to investigate the influence of growth ring orientation on the rolling shear properties. The experimental results showed that the growth ring orientation had a significant effect on rolling shear modulus of WCL, however, almost no effect on the rolling shear strength. The WCL of in-between end grain had the maximum rolling shear modulus of 89MPa and rolling sh ear strength of 2.13 MPa.
It has been shown that measurement of elastic constants of orthotropic wood-based panel products can be more efficiently measured by modal testing technique. Identification of vibration modes and corresponding natural frequencies is key to the application of modal testing technique. This process is generally tedious and requires a number of measurement locations for mode shape identification. In this study, a simplified method for frequency identification was developed which will facilitate the adoption of the vibration-based testing technique for laboratory and industrial application. In the method, the relationship between frequency order and mode order is first studied considering the boundary condition, elastic properties of the orthotropic panel. An algorithm is proposed to predict the frequency values and mode indices based on corresponding normalized sensitivity to elastic constants, initial estimates of orthotropic ratios and measured fundamental natural frequency. The output from the algorithm can be used for identification of sensitive natural frequencies from up to three frequency spectra. Then the algorithm is integrated with the elastic calculation algorithm to extract the elastic constants from the sensitive frequencies. The elastic constants of cross laminated timber panels were measured by the proposed method. The moduli of elasticity agree well with static testing results. The calculated in-plane shear modulus was found to be within the expected range.
Cross laminated timber (CLT) is leading the evolution of wood construction throughout the world. As atwo-dimensional plate-like construction product, the in-plane elastic constants of CLT panels are the fundamental parameters for serviceability design. The elastic constants including moduli of elasticity (MOE) in major and minor strength direction ( and y) and in-plane shear modulus ( xy) of full-size CLT panels with different dimensions and layups from three CLT producers were measured by a non-destructive test (NDT) method developed by the first author. In total, 51 CLT panels were tested with most of the testing conducted at CLT mills. The measured values were used to examine the existing effective stiffness prediction models of CLT. Results show that k-method can be used for predicting and y values of industrial size CLT with a large length/ width to thickness ratio. xy cannot be well predicted by k-method and is greatly affected by edge bonding and gaps. Gamma method and shear analogy method can include the effect of transverse shear to different extents into account in predicting apparent or y. Shear analogy method appears to predict closer apparent to the measured values than gamma method for CLT with small length to thickness ratio. However, the effect of transverse shear on apparent y is not as much as predicted by shear analogy method for CLT panels with width from 1 to 3 meters. NDT by modal testing was proven to be an efficient mechanical property evaluation method for full-size CLT panels.
Massive timber panels (MTPs) has shown a great potential in construction of tall buildings. Evaluation of the face-bond strength of MTPs is of an interest to use of this kind of products. This study was aimed at developing an appropriate test procedure for evaluating the adhesive bond strength of cross-laminated laminated strand lumber (LSL). Short span bending tests were conducted on two-layer asymmetric cross-laminated LSL specimens, which were adhesively bonded using two-component polyurethane (PUR) and polyvinyl acetate (PVAc). For comparison, block shear specimens were tested as well. It was found that the 2-layer asymmetric cross-laminated specimen assembly under the short span bending could be used to differentiate between good and poor bond quality.