Using Charles and Ray Eames’s famous 1950s House of Cards slotting toy as both design metaphor and structural precedent provides the starting point for a novel building logic (utilising three existing Swedish timber systems) that allows volumetrically slotted units to stack inside of and support each other. Contemporary computer-aided fabrication techniques based on evolutionary algorithms and CNC manufacturing strategies are used to produce a methodology for designing a kit-of-parts system at the scale of the skyscraper, based on the slotting together of cross-laminated timber (CLT) panels. A catalogue of novel slotting methods is produced, and a number of alternative slotted joint treatments identified that hold promising potential for further development, parametrically design and control volumes, understand the fabrication workflow and constructional sequence on site, and build prototypes of the chosen slotting configurations at scales ranging between 1:50 and 1:1.
The ambient movement of three modern multi-storey timber buildings has been measured and used to determine modal properties. This information, obtained by a simple, unobtrusive series of tests, can give insights into the structural performance of these forms of building, as well as providing information for the design of future, taller timber buildings for dynamic loads. For two of the buildings, the natural frequency has been related to the lateral stiffness of the structure, and compared with that given by a simple calculation. In future tall timber buildings, a new design criterion is expected to become important: deflection and vibration serviceability under wind load. For multi-storey timber buildings there is currently no empirical basis to estimate damping for calculation of wind-induced vibration, and there is little information for stiffness under wind load. This study therefore presents a method to address those gaps in knowledge.
This paper investigates the risk of disproportionate collapse following extreme loading events. The methodology mimics a sudden removal of a loadbearing wall of a twelve-storey CLT building. The ductility-demand from the dynamic simulation is checked against the ductility supplied by the structural components and their connections. The analyses focus on rotational stiffness (k) of the joints by considering three different sub-structural idealisations according to the required modelling details and the feasibility of model reductions. To resist the imposed dynamic forces, the required k-values may be too large to be practically achieved by means of off-the-shelf brackets and screw connections. Improved structural detailing as well as adequate thickness of structural elements need to be considered in order to reduce the probability of disproportionate collapse.
This paper discusses the impact of the natural frequency of multi-storey timber structures, focusing on force-based seismic design. Simplified approaches to determine the frequency of light-frame and cross-laminated timber structures are investigated. How stiffness parameters for simple two-dimensional analysis models can be derived from the different contributions of deformation...
Composite structures use the advantages of two materials – timber and concrete – and improve the efficiency of a material application. Especially the concept of timber-concrete-composite ceilings has synergetic effects to achieve an effective ratio of thickness to span with high cost effectiveness simultaneously. Following the systematic...
In this work the behaviour of hybrid multi-storey buildings braced with Cross-Laminated-Timber (CLT) cores and shear-walls is studied based on numerical analyses. Two procedures for calibrating numerical models are adopted and compared to test data and application of provisions in current design codes. The paper presents calibration of parameters characterising connections used to interconnect adjacent CLT panels and building cores, and attach shear-walls to foundations or floors that act as eleveted diaphragms. Different case studies are analysed comparing the structural responses of buildings assembled with „standard" fastening systems (e.g. hold-downs and angle-brackets), or using a special X-RAD connection system. The aim is to characterize behaviours of connections in ways that reflect how they perform as parts of completed multi-storey superstructure systems, rather than when isolated from such systems or their substructures. Results from various analyses are presented in terms of principal elastic periods, base shear forces, and uplift forces in buildings. Discussion addresses key issues associated with engineering analysis and design of buildings having around five or more storeys.
The paper presents the design and detailing, and the experimental quasi-static 2/3 scale tests of two posttensioned wall systems: a single (more traditional) wall system (Figure 2) and a new configuration comprising of a column-wall-column coupled system (Figure 3). The latter allows avoiding displacement incompatibilities issues between the wall and the diaphragm by using the boundary columns as supports.
New Zealand Society for Earthquake Engineering Conference
April 10-12, 2015, Rotorua, New Zealand
This paper discusses the design of timber diaphragms, in response to the growing interest in multi-storey commercial timber structures, and the lack of guidance or regulations regarding the seismic design of timber diaphragms.
Proper performance of floor diaphragms is required to transfer all lateral loads to the vertical systems that resist them, but design for earthquake loads can be more complex than design for wind loads. This paper confirms that the seismic design of a diaphragm is intimately linked to the seismic design of the whole building. Diaphragm failure, even if restricted to a limited diaphragm portion, can compromise the behaviour of the whole building. It is therefore necessary to design and detail diaphragms for all possible load paths and to evaluate their influence on the load distribution within the rest of the structure. It is strongly recommended that timber diaphragms be designed as elastic elements, by applying dynamic amplification and overstrength factors derived from the lateral load resisting system.
This paper shows that some current design recommendations for plywood sheathing on light timber framing can be applied to massive wood diaphragms, but for more complex floor geometries an equivalent truss method is suggested. Diaphragm flexibility and displacement incompatibilities between the floor diaphragms and the lateral resisting systems also need to be accounted for.