In this paper a precise model is established for deflection prediction of mechanically jointed beams with partial composite action. High accuracy of the proposed method is demonstrated through comparison with a comprehensive finite element (FE) modelling for a timber-concrete partial composite beam. Next, the obtained numerical results are compared with gamma-method, a well-known simplified solution for timber engineers according to the Eurocode 5. Validity and accuracy level of the gamma-method are investigated for various boundary conditions as well as different values of beam length-to-depth ratio, and discussed in details.
Strength parameters for fasteners determined in accordance with the methods prescribed for the European CE-marking leads to quite different values for seemingly similar products from different manufactures. The results are hardly repeatable, to some extent due to difficulties in selecting representative timber samples for the testing. Beside this uncertainty, the declared values available to the designer concerns only structural timber, so no strength parameters are available for common engineered wood products such as LVL or plywood.
This paper gives:
Examples of the variability of declared strength parameters for ring shank nails for almost similar products.
Results from withdrawal test for similar nails inserted in the same timber specimens (structural timber and LVL), which is used for investigating similarities and differences between nails and wood.
Discussion of statistical methods to compare the strength parameters of two nails.
A proposal for a method that enables to determine accurate strength parameters needed for structural design from comparative tests involving reference fasteners.
A major problem in light-weight timber floors is their insufficient performance coping with impact noise in low frequencies. There are no prefabricated solutions available in Australia and New Zealand. To rectify this and enable the implementation of light-weight timber floors, a structural floor was designed and built in laminated veneer lumber (LVL). The floor was evaluated in a laboratory setting based on its behaviour and then modified with suspended ceilings and different floor toppings. Twenty-nine different floor compositions were tested. The bare floor could not reach the minimum requirement set by the Building Code of Australia (BCA) but with additional layers, a sufficient result of R'w+Ctr 53 dB and L’nT,w + CI 50 dB was reached. Doubling of the concrete mass added a marginal improvement. With concrete toppings and suspended ceiling it is possible to reach the goal in airborne and impact sound insulation. The best result was achieved by combining of additional mass and different construction layers.
The advantages of the two different building construction materials, timber and concrete, can be used effectively in adhesive-bonded timber-concrete composite constructions. The long-term behavior was investigated experimentally on small-scale shear and bond specimens under artificial, alternating climatic conditions and on fullscale specimens under natural climatic conditions for an application in construction practice. The development of the shear strength and the deformation behavior under permanent loads were studied, focusing on the different material behavior of wood and concrete regarding changes in temperature and moisture. The general applicability of adhesivebonded timber-concrete composites in construction practice was proved in the investigations.
Wooden constructions are on the rise again – encouraged by a strong trend towards sustainable and resource efficient buildings. Load-bearing timber-glass composite elements – a novel concept to use the in-plane loadbearing potential of glass – could contribute to a more efficient use of materials in façades. The current study relates to the adhesive bond between the glass pane and the timber substructure. The applicability of structural sealants such as silicones is limited due to their distinct flexibility which leads to large deformations of the joint. Further potential arises from the use of adhesives of medium and high stiffness. Their general performance as well as their durability have not yet been evaluated with respect to the proposed use in building constructions. This paper draws attention to the ageing stability of two promising adhesives. Small-scale adhesively bonded specimens which are composed of a wooden and a glass piece are exposed to different ageing scenarios which relate to the impacts typically encountered in façades. Based on the results it can be concluded that the considered high-modules adhesives enable an increase of characteristic failure loads and a reduction of joint deformation, but also reveal shortcomings regarding their ageing stability.
The following topics in the field of seismic analysis and design of mid-rise (5- and 6-storey) wood-frame buildings are included in this paper: Determination of the building period, linear dynamic analysis of wood-frame structures, deflections of stacked multi-storey shearwalls, diaphragm classification, capacity-based design for woodframe...
In this paper, possibilities and challenges of novel robotic manufacturing processes for segmented timber shells are presented and evaluated. This is achieved by comparing two newly developed construction systems for segmented plate structures: one system consisting of cross-laminated timber elements that are connected with crossing screws, and one system consisting of light-weight, hollow components with finger joints as well as bolted connections. Segmented timber shells are introduced as an emerging structural typology transitioning from applied research to the building industry, enabled by new developments in computational design and digital fabrication methods. Although the two construction systems share their underlying segmentation strategy, they differ in their joint design approach and ensuing fabrication complexity. While the first construction system can be produced with conventional machining technology in the timber industry, the second system was developed in conjunction with innovative robotic manufacturing methods. In order to evaluate the relationships and trade-offs of fabrication complexity and performance, the two systems are compared on a range of metrics, including material use, environmental impact and costs.
Using Charles and Ray Eames’s famous 1950s House of Cards slotting toy as both design metaphor and structural precedent provides the starting point for a novel building logic (utilising three existing Swedish timber systems) that allows volumetrically slotted units to stack inside of and support each other. Contemporary computer-aided fabrication techniques based on evolutionary algorithms and CNC manufacturing strategies are used to produce a methodology for designing a kit-of-parts system at the scale of the skyscraper, based on the slotting together of cross-laminated timber (CLT) panels. A catalogue of novel slotting methods is produced, and a number of alternative slotted joint treatments identified that hold promising potential for further development, parametrically design and control volumes, understand the fabrication workflow and constructional sequence on site, and build prototypes of the chosen slotting configurations at scales ranging between 1:50 and 1:1.
Wood preservation is an important issue for agricultural buildings with timber structure. This is among others due to their halfway opened construction, high level of moisture release from livestock breeding or storing goods. However, regarding the possibly high moisture content in the building structure and the potential threat caused by wood-destroying organisms, there is still a substantial need for research. The latest results of the research work carried out by Technical University of Munich, in cooperation with the Bavarian State Research Center for Agriculture, show that, for the most agricultural buildings built from spruce, no preventative chemical wood preservation is necessary to ensure a durable construction.
The airtightness of building must be measured for the evaluation of building energy performance. To make up the reference airtightness value of wooden houses built in Korea, blower door test was carried out in the 36 houses. And, during the test, the causes of air leakage were inspected simultaneously. The result showed that the average of ACH50((air change per hour at air pressure difference 50Pa) measured from light timber frame houses was 3.5 h-1 and the post-beam construction was 5.1h-1. And, insulation with form of foams was advantageous in ensuring building airtightness than glass fiber batt. And, values below 1.5 h-1 of ACH50, threshold for application of artificial air change equipment, had appeared after 2010s. Also, the values varied according to who managed the building construction field. Although only one measurement of CLT(cross laminated timber) residential building could be obtained in 2016, the result showed good airtightness of building with 0.7 h-1.