For wood floor systems, their vibration performance is significantly dependent on the conditions of their supports, specifically the rigidity of the support. Detrimental effects could result if the floor supports do not have sufficient rigidity. This is special ture for floor supporting beams. The problem of vibrating floor due to flexible supporting beams can be solved through proper design of the supporting beams. However, there is currently no criterion set for the minimum requirement for floor supporting beam stiffness to ensure the beam is rigid enough. Designers’ current practice is to use the uniform load deflection criteria specified in the code for designing the supporting beams. This criterion is based on certain ratios of the floor span (e.g. L/360, L/480 etc.). The disadvantage of this approach is that it allows larger deflections for longer-span beams than for shorter beams. This means that engineers have to use their experience and judgement to select a proper ratio, particularly for the long-span beams. Therefore, a better vibration-controlled design criterion for supporting beams is needed.
It is recommended to further verify the ruggedness of the proposed stiffness criterion for floor supporting beams using new field supporting beam data whenever they become available.
A regular alternation of lamellas and voids filled by insulating material within each layer of CLT can lead to cellular panels with improved acoustical, thermal and fire performance. In order to support the development of these innovative and lighter engineered wood products, their mechanical behavior is investigated in this paper by means...
Within this paper the material and structural influences of orthogonal to the span oriented outer layers of multilayered plates are investigated. Therefore the influences on the bending stiffness and the bending capacity are examined...
At the Institute of Structural Engineering at the ETH Zurich numerous of investigations are
conducted to analyse the load bearing capacity of glued laminated timber beams. The investigations are part of the research project ’Influence of varying material properties on the load bearing capacity of glued laminated timber (glulam)’.
The investigations are taking place on 24 glulam beams with well-known material properties.
The glulam beams are fabricated out of 400 timber boards. From those boards the material
properties are investigated non-destructively within a former research project. During the glulam
fabrication it is particularly focused to keep the information of the timber boards; i.e. after the
glulam fabrication the position of each particular timber board within the glulam beam and
thus the position of each particular knot is still known.
The glulam beams are investigated during a 4-point bending test. On the glulam members
the load bearing capacity, the bending stiffness and the density is measured. Furthermore
local strains within the glulam beams are investigated using an optical coordinate-measurement
device. Following the test the failure is investigated in detail. Hereby the type of failure (knot
cluster, finger joint, clear wood) and the amount of failure (number of damaged lamellas) is
documented. Afterwards the failed glulam beams are loaded again to analyse the remaining
bending strength and the corresponding remaining bending stiffness.
The major aim of the experimental analysis is the investigation of the load bearing capacity
of glulam beams with well-known local material properties. The gained results can be used for
an investigation of the influence of local weak zones, such as knot clusters or finger joints, on the
load bearing capacity of glulam. In addition a data basis is produced to develop a new model
(or to evaluate existing models) for the estimation of the load bearing capacity of glulam.
The design of cross-laminated solid timber (CLT) as load-bearing plates is mainly governed by serviceability criterions like maximal deflection and susceptibility to vibration. Hence, predicting the respective behavior of such plates requires accurate information about their elastic properties. According to product standards, the bending stiffness of CLT has to be assessed from 4-point bending tests of strip-shaped specimens, cut from the CLT panels. By comparing elastic properties of CLT derived by means of modal analysis of full panels with the results of bending tests on 100 mm and 300 mm wide strip-shaped specimens it is shown, that by testing single 100 mm wide strip-shaped specimens bending stiffness of full panels cannot be assessed correctly, whereas single 300 mm wide strips or averages of 5 to 6 100 mm wide strip-shaped specimens lead to acceptable results. Hence, strip-shaped specimens should only be used in the course of factory quality control or when assessing the bending stiffness of parts of CLT panels used as beam-like load-bearing elements but not to derive bending stiffness of gross CLT panels. Verification by carrying out static bending tests of gross CLT panels under different loading situations showed that alternatively to tests on strip-shaped specimens or estimations with the compound theory, the overall stiffness properties of CLT can be derived directly by a modal analysis of full-size panels.
Wood-concrete composite slab floors provide a promising solution for achieving long spans and shallow wood-based floor systems for large and tall wood buildings. In comparison with conventional wood floor systems, such long span and heavy floors have a lower fundamental natural frequency...
Traditional wood-wood connections, widely used in the past, have been progressively replaced by steel fasteners and bonding processes in modern timber constructions. However, the emergence of digital fabrication and innovative engineered timber products have offered new design possibilities for wood-wood connections. The design-to-production workflow has evolved considerably over the last few decades, such that a large number of connections with various geometries can now be easily produced. These connections have become a cost-competitive alternative for the edgewise connection of thin timber panels. Several challenges remain in order to broaden the use of this specific joining technique into common timber construction practice: (1) prove the applicability at the building scale, (2) propose a standardized construction system, (3) develop a convenient calculation model for practice, and (4) investigate the mechanical behavior of wood-wood connections. The first building implementation of digitally produced through-tenon connections for a folded-plate structure is presented in this work. Specific computational tools for the design and manufacture of more than 300 different plates were efficiently applied in a multi-stakeholder project environment. Cross-laminated timber panels were investigated for the first time, and the potential of such connections was demonstrated for different engineered timber products. Moreover, this work demonstrated the feasibility of this construction system at the building scale. For a more resilient and locally distributed construction process, a standardized system using through-tenon connections and commonly available small panels was developed to reconstitute basic housing components. Based on a case-study with industry partners, the fabrication and assembly processes were validated with prototypes made of oriented strand board. Their structural performance was investigated by means of a numerical model and a comparison with glued and nailed assemblies. The results showed that through-tenon connections are a viable alternative to commonly used mechanical fasteners. So far, the structural analysis of such construction systems has been mainly achieved with complex finite element models, not in line with the simplicity of basic housing elements. A convenient calculation model for practice, which can capture the semi-rigid behavior of the connections and predict the effective bending stiffness, was thus introduced and subjected to large-scale bending tests. The proposed model was in good agreement with the experimental results, highlighting the importance of the connection behavior. The in-plane behavior of through-tenon connections for several timber panel materials was characterized through an experimental campaign to determine the load-carrying capacity and slip modulus required for calculation models. Based on the test results, existing guidelines were evaluated to safely apply these connections in structural elements while a finite element model was developed to approximate their performance. This work constitutes a firm basis for the optimization of design guidelines and the creation of an extensive database on digitally produced wood-wood connections. Finally, this thesis provides a convenient design framework for the newly developed standardized timber construction system and a solid foundation for research into digitally produced wood-wood connections.