Skip header and navigation

43 records – page 1 of 5.

Experimental Investigations of Shear Connections with Self-Tapping-Screws for Cross-Laminated-Timber Panels

https://research.thinkwood.com/en/permalink/catalogue2295
Year of Publication
2019
Topic
Design and Systems
Connections
Material
CLT (Cross-Laminated Timber)
Application
Wood Building Systems

Fire Resistance of Unprotected Cross-Laminated Timber (CLT) Floor Assemblies Produced in the USA

https://research.thinkwood.com/en/permalink/catalogue2507
Year of Publication
2019
Topic
Fire
Design and Systems
Material
CLT (Cross-Laminated Timber)
Application
Floors
Wood Building Systems

Cyclic Load Behaviour of Beam-to-Column Glulam Joints Combining Glued-in Rods with Steel Brackets

https://research.thinkwood.com/en/permalink/catalogue2028
Year of Publication
2018
Topic
Connections
Mechanical Properties
Material
Glulam (Glue-Laminated Timber)

Development of a Spring Model for the Structural Analysis of a Double-Layered Timber Plate Structure with Through-Tenon Joints

https://research.thinkwood.com/en/permalink/catalogue2034
Year of Publication
2018
Topic
Design and Systems
Mechanical Properties
Connections
Material
LVL (Laminated Veneer Lumber)
Author
Chi Nguyen, Anh
Weinand, Yves
Year of Publication
2018
Country of Publication
South Korea
Format
Conference Paper
Material
LVL (Laminated Veneer Lumber)
Topic
Design and Systems
Mechanical Properties
Connections
Keywords
Beech
Joints
Finite Element Model
Double-Layered Timber Plate
Stiffness
Language
English
Conference
World Conference on Timber Engineering
Research Status
Complete
Online Access
Free
Resource Link
Less detail

Effect of Rod-to-Grain Angle on Capacity and Stiffness of Axially and Laterally Loaded Long Threaded Rods in Timber Joints

https://research.thinkwood.com/en/permalink/catalogue1371
Year of Publication
2018
Topic
Connections
Mechanical Properties
Material
Glulam (Glue-Laminated Timber)
Author
Cepelka, Martin
Arne Malo, Kjell
Stamatopoulos, Haris
Publisher
Springer Berlin Heidelberg
Year of Publication
2018
Country of Publication
Germany
Format
Journal Article
Material
Glulam (Glue-Laminated Timber)
Topic
Connections
Mechanical Properties
Keywords
Threaded Rods
Axial Loads
Lateral Loads
Rod-to-Grain
Joints
Boundary Conditions
Load-to-Rod
Language
English
Research Status
Complete
Series
European Journal of Wood and Wood Products
ISSN
1436-736X
Summary
Long threaded rods have recently been widely used as a reinforcement of glued laminated timber in perpendicular to the grain direction. The recent research has thus focused mainly on the withdrawal properties of the threaded rods in the axial direction. Utilizing their large withdrawal stiffness and strength, the threaded rods can also effectively be used as connectors in moment resisting timber joints. Yet, in joints, the threaded rods are often imposed to a non-axial loading, due to inclination of the rod axis to the grain as well as loading direction different from the rod axis. No design models are currently available for the combined axial and lateral loading of the threaded rods. In the present work, the effects of the rod-to-grain and load-to-rod angles on capacity and stiffness of the threaded rods are investigated by use of experiments and finite element models. Based on those, analytical expressions for determining stiffness and capacity of axially and laterally loaded threaded rods are proposed, intended as a basis for practical joint design. Furthermore, effect of various boundary conditions applied at the rod-ends is studied.
Online Access
Free
Resource Link
Less detail

Extended End Plate Semi-Rigid Composite Joints with CLT Panels and Demountable Shear Connectors

https://research.thinkwood.com/en/permalink/catalogue2059
Year of Publication
2018
Topic
Connections
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Application
Frames

Investigating the Hysteretic Behavior of Cross-Laminated Timber Wall Systems due to Connections

https://research.thinkwood.com/en/permalink/catalogue1230
Year of Publication
2018
Topic
Connections
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Application
Walls
Author
Izzi, Matteo
Polastri, Andrea
Fragiacomo, Massimo
Publisher
American Society of Civil Engineers
Year of Publication
2018
Country of Publication
United States
Format
Journal Article
Material
CLT (Cross-Laminated Timber)
Application
Walls
Topic
Connections
Mechanical Properties
Keywords
Numerical Model
Mechanical Behavior
Failure Mechanisms
Anchoring
Joints
Load-Displacement
Energy Dissipation
Language
English
Research Status
Complete
Series
Journal of Structural Engineering
Summary
Cross-laminated timber (CLT) wall systems are composed of massive timber panels that are fastened together and to the horizontal elements (foundations or intermediate floors) with step joints and mechanical connections. Due to the high in-plane stiffness of CLT, the shear response of such systems depends strongly on the connections used. This paper proposes a numerical model capable of predicting the mechanical behavior and failure mechanisms of CLT wall systems. The wall and the element to which it is anchored are simulated using three-dimensional (3D) solid bodies, while the connections are modeled as nonlinear hysteretic springs. Typical racking tests of wall systems are reproduced by varying the assumptions used to schematize the behavior of the connections. Results are compared with test data published in the literature, and the differences are discussed. The influence of the boundary conditions (vertical load applied on top of the wall and friction at its base) and aspect ratio of the panel are investigated via a parametric numerical study. Finally, the performance of a wall system assembled with two CLT panels is analyzed, highlighting how the properties of the anchoring connections and vertical step joints affect the load-displacement response and energy dissipation.
Online Access
Free
Resource Link
Less detail

Strength and Stiffness of CLT Shear Walls in Platform Construction

https://research.thinkwood.com/en/permalink/catalogue1976
Year of Publication
2018
Topic
Design and Systems
Connections
Mechanical Properties
Material
CLT (Cross-Laminated Timber)
Application
Walls
Wood Building Systems

Systematic Experimental Investigation to Support the Development of Seismic Performance Factors for Cross Laminated Timber Shear Wall Systems

https://research.thinkwood.com/en/permalink/catalogue1281
Year of Publication
2018
Topic
Seismic
Material
CLT (Cross-Laminated Timber)
Application
Shear Walls
Author
Amini, Omar
van de Lindt, John
Rammer, Douglas
Pei, Shiling
Line, Philip
Popovski, Marjan
Publisher
ScienceDirect
Year of Publication
2018
Country of Publication
Netherlands
Format
Journal Article
Material
CLT (Cross-Laminated Timber)
Application
Shear Walls
Topic
Seismic
Keywords
Quasi-Static
Cyclic Tests
Stiffness
Strength
Deformation
Aspect Ratios
Thickness
Joints
Language
English
Research Status
Complete
Series
Engineering Structures
Summary
In the US, codified seismic design procedure requires the use of seismic performance factors which are currently not available for CLT shear wall systems. The study presented herein focuses on the determination of seismic design factors for CLT shear walls in platform type construction using the FEMA P-695 process. Results from the study will be proposed for implementation in the seismic design codes in the US. The project approach is outlined and selected results of full-scale shear wall testing are presented and discussed. Archetype development, which is required as part of the FEMA P-695 process, is briefly explained with an example. Quasi-static cyclic tests were conducted on CLT shear walls to systematically investigate the effects of various parameters. The key aspect of these tests is that they systematically investigate each potential modelling attribute that is judged within the FEMA P-695 uncertainty quantification process. Boundary constraints and gravity loading were both found to have a beneficial effect on the wall performance, i.e. higher strength and deformation capacity. Higher aspect ratio panels (4:1) demonstrated lower stiffness and substantially larger deformation capacity compared to moderate aspect ratio panels (2:1). However, based on the test results there is likely a lower bound for aspect ratio (at 2:1) where it ceases to benefit deformation capacity of the wall. This is due to the transition of the wall behaviour from rocking to sliding. Phenomenological models were used in modelling CLT shear walls. Archetype selection and analysis procedure was demonstrated and nonlinear time history analysis was conducted using different wall configurations.
Online Access
Free
Resource Link
Less detail

43 records – page 1 of 5.