This paper deals with a certain type of C.L.T. (Cross Laminated Timber) construction, in a residential building in Fristad, Sweden. The objective is to study impact noise transmission, at the lower frequency range (10-200 Hz), where wooden dwellings perform inefficiently, in terms of acoustic quality. The vibrational behavior of lightweight structures and specifically a multilayered floor separating two vertically adjacent bedrooms are investigated. A numerical model of the multilayered test plate, which includes sound insulation and vibration isolation layers, is developed using the Finite Element Method (F.E.M.) in commercial software. The design process, the analysis and improvement of the calculated outcome concerning accuracy and complexity are of interest. In situ vibration measurements were also performed so as to evaluate the structures dynamic behavior in reality and consequently the validity of the modelled results. The whole process from design to evaluation is discussed thoroughly, where uncertainties of the complex F.E.M. model and the approximations of the real structure are analyzed. Numerical comparisons are presented including mechanical mobility and impact noise transmission results. The overall aim is to set up a template of calculations that can be used as a prediction tool in the future by the industry and researchers.
There is a strong trend to industrially produce multi-storey light weight timber based houses. This concept allows the buildings to be manufactured to a more or less prefabricated extent. Most common types are volume/room modules or flat wall and floor modules. When assembling the modules at the building site, elastomer isolators are used in several constructions to reduce flanking transmission. The sound insulation demands in the Nordic countries are relatively high and therefore the flanking transmission must be well controlled, where elastomer isolators are an alternative. Decoupled radiation isolated walls is another. There are though no working studies or mathematical models of the performance of these isolators. They are only treated as simple mass-springs systems that operate vertically, i.e. one degree of freedom. In this paper there is an analysis of experimentally data of the structure borne sound isolating performance of elastomer isolators that are separating an excited floor from receiving walls. The performance dependence of structure type is also presented. An empirically based regression model of the vibration level difference is derived. The model is based on measurements of six elastomer field installations, which are compared to five comparable installations without elastomers. A goal is that the model can be used for input in future SEN prediction models for modeling of sound insulation.
This paper presents the first results of the flanksound project, a study promoted by Rotho Blaas srl regarding flanking transmission between CLT panels jointed with different connection systems. The vibration reduction index Kij is evaluated according to the EN ISO 10848 standard by measuring the velocity level difference between CLT panels. The performance of the X-RAD connection system is compared to the performance of a traditional connection system made of shear angle bracket and hold-down, both the configurations being tested with and without a resilient material placed between the construction elements. Concerning the traditional system, the influence of the difference sizes and types of fasteners - including the method of nailing or screwing - was also evaluated. The results of the measurements exposed in this work will hopefully contribute to the development of the acoustic design of timber buildings by providing a solid database of Kij values, which can be used to forecast the acoustic performance of the building according to the prediction models proposed in EN 12354-1.
In recent years Cross Laminated Timber (CLT) was introduced as an emerging building system in the North American market. CLT elements consist of multiple layers of wooden beams that are laid-out cross-wise and laminated together to form solid wood panels for floors and walls. As part of a multi-disciplinary research project a comprehensive study was conducted on the impact and airborne sound insulation of this type of elements in order to create a data base that allows building designers to predict the acoustic performance of CLT systems. Parametric studies were carried out on the direct impact airborne sound insulation of CLT floor assemblies (with/ without various floor topping and gypsum board ceiling variants), on the direct airborne sound insulation of CLT walls (with/without gypsum board linings), as well as on the structure-borne sound transmission on a series of CLT building junctions. The results were then used as input data for predictions of the apparent impact and airborne sound insulation in real CLT buildings using the ISO 15712 (EN12354) framework that was originally developed for concrete and masonry buildings. The paper presents the prediction approach as well as results of prediction and measurement series for apparent impact and airborne sound insulation.
Cross Laminated Timber (CLT), which is well suited for construction of tall buildings, is becoming a more popular construction material in North America. However, to ensure comfortable living conditions, sound insulation measures are necessary. The study presented here compares results of direct impact sound insulation of 5- and 7-ply CLT floors covered with different a concrete toppings on various interlayers. Improvements of up to 21dB in Weighted Normalized Impact Sound Pressure Level (Ln,w) were observed using a newly proposed reference floor for CLTs. Furthermore, the improvements of floor coverings on CLT floors are compared to those achieved on other types of construction, such as the reference concrete floor. The improvements of Ln,w tend to be higher on the concrete floors than on the CLT floors tested. These and other findings will be presented.
This research paper deals with the evaluation of the dynamic modal vibration tests conducted on an innovative timber structure, the ETH House of Natural Resources. The building serves as a demonstrator of several innovative structural systems and technologies relating to timber. The main load-bearing structure comprises a posttensioned timber frame, which was subjected to modal vibration tests, firstly in the laboratory and, subsequently on the construction site. In this paper, the modal characteristics (eigenfrequencies, damping ratios and mode shapes), obtained from the laboratory testing campaign are presented. The modal vibration data is evaluated using polynomial and subspace identification techniques. The obtained results reveal that the structure exhibits pure translational, beam and column modes, as well as mixed beam-column modes. The bottom connection of the columns delivers significant influence on the modal characteristics, whereas the level of post-tensioning force yields no substantial influence in the modal characteristics obtained from low amplitude modal vibration tests.