Ninth European Conference on Noise Control (Euronoise)
June 10-13, 2012, Prague, Czech Republic
In residential multi-storey buildings of timber it is of great importance to reduce the flanking transmission of noise. Some building systems do this by installing a vibration-damping elastic interlayer, Sylomer or Sylodyn , in the junction between the support and the floor structure. This interlayer also improves the floor vibration performance by adding damping to the structure. In the present work the vibration performance of a floor with such interlayers has been investigated both in laboratory and field tests. A prefabricated timber floor element was tested in laboratory on rigid supports and on supports with four different types of interlayers. The results are compared with in situ tests on a copy of the same floor element. The effect on vibration performance i.e. frequencies, damping ratio and mode shapes is studied. A comparison of the in situ test and the test with elastic interlayer in laboratory shows that the damping in situ is approximately three times higher than on a single floor element in the lab. This indicates that the damping in situ is affected be the surrounding building structure. The achieved damping ratio is highly dependent on the mode shapes. Mode shapes that have high mode shape coefficients along the edges where the interlayer material is located, result in higher modal damping ratios. The impulse velocity response, that is used to evaluate the vibration performance and rate experienced annoyance in the design of wooden joist floors, seems to be reduced when adding elastic layers at the supports.
Le présent rapport décrit une partie des activités de recherche et développement (R&D) en lien avec la démonstration de la résistance au feu ainsi que les études sur la performance acoustique effectuées dans le cadre de la construction du bâtiment Origine. Ce bâtiment est la tour résidentielle en bois massif la plus haute au Québec. Sa réalisation a débuté en 2015 à la suite des analyses préliminaires de faisabilité technique-économique qui se sont étalées pendant toute l’année 2014. La construction et l’installation se sont finalisées vers la fin de 2017.
En premier lieu, le rapport présente les démarches liées à la réalisation d’un exercice de démonstration d’incendie pour une cage d’escaliers/ascenseur avec une chambre d’habitation adjacente, l’analyse de résultats et les principales conclusions en lien avec la pertinence de l’utilisation du bois massif pour des édifices de grande hauteur. En ce qui concerne la performance acoustique, le rapport présente la méthodologie d’étude et d’analyse des résultats des tests acoustiques pour des assemblages de mur et de plancher utilisés dans le projet Origine. De plus, ce rapport facilite la compréhension des activités réalisées et permet de montrer objectivement la capacité des produits en bois massif à offrir un environnement sécuritaire et confortable aux occupants de bâtiments multi-étagés.
Les principaux résultats indiquent que les cages d’escaliers/ascenseur faites en bois massif, conçues pour une résistance au feu équivalente à celle faites en béton, peuvent offrir une excellente performance et servent d’alternatives adéquates pour les bâtiments multi-étagés. En ce qui concerne le développement d’assemblages acoustiques pour les murs et les planchers en bois massif, il a été prouvé qu’une approche multicritère permet d’offrir des solutions performantes à des coûts raisonnables.
Finalement, il est clair que ce projet constitue un jalon très important dans le chemin d’acceptation des bâtiments multi-étagés en bois massif au Québec et au Canada. Sa construction, faite presque entièrement en bois, a nécessité de nombreux efforts économiques, de R&D, de conception et d’installation. De plus, les activités réalisées pour l’acceptation de ce type de construction ont permis de mettre en place de nouvelles technologies et des techniques de conception qui faciliteront la réplication de ce type de projet partout en Amérique du Nord.
This paper deals with the comfort properties in a planned 14-storey timber apartment building in Bergen, Norway. The building will be one of the tallest timber buildings in the world. The building consists of load-carrying glulam trusses with two intermediate strengthened levels. The truss carries prefabricated building modules. Herein, the evaluation with respect to dynamic behaviour of the building is described with emphasis on the horizontal acceleration due to wind forces.
"Treet" is a relatively high building with low structural weight. Its natural frequencies lie in the domain where wind can cause annoying motions or nausea. The stiffness and mass properties for glulam and concrete are well known, but poorly described for complex, complete building modules. To get better knowledge of dynamic behaviour of the prefabricated building modules, testing was needed. Based on the structural design and the module testing a FEM analysis model was generated in order to calculate the building's natural frequencies and modal mass. These parameters were used to determine the windinduced accelerations of "Treet".
The ambient movement of three modern multi-storey timber buildings has been measured and used to determine modal properties. This information, obtained by a simple, unobtrusive series of tests, can give insights into the structural performance of these forms of building, as well as providing information for the design of future, taller timber buildings for dynamic loads. For two of the buildings, the natural frequency has been related to the lateral stiffness of the structure, and compared with that given by a simple calculation. In future tall timber buildings, a new design criterion is expected to become important: deflection and vibration serviceability under wind load. For multi-storey timber buildings there is currently no empirical basis to estimate damping for calculation of wind-induced vibration, and there is little information for stiffness under wind load. This study therefore presents a method to address those gaps in knowledge.
This paper discusses the impact of the natural frequency of multi-storey timber structures, focusing on force-based seismic design. Simplified approaches to determine the frequency of light-frame and cross-laminated timber structures are investigated. How stiffness parameters for simple two-dimensional analysis models can be derived from the different contributions of deformation...
An effort to use renewable materials leads to broader utilization of timber structures also for multi-storey buildings. However, wider application of timber floor structures in multi-storey buildings is limited by lower lateral rigidity, worse acoustic and fire safety parameters in comparison to concrete floor structures. The composite floor structures based on high performance silicates and wood represent the beneficial alternative to the modern timber floor structures. Proposed timber-concrete composite floor structure benefits from lower weight of slender HPC or UHPC deck (compared to common RC slab) while improving acoustic parameters and ifre safety of the structure (compared to timber floor structure). Experimental verification proved that effective mechanical connection can be ensured by gluing.
Key words: timber-concrete, high performance concrete, floor structures, experimental verification, glued connection.
This new study aims to generate hygrothermal, particularly moisture-related performance data for light wood-frame walls meeting the R22 effective (RSI 3.85) requirement for buildings up to six storeys in the City of Vancouver. The overarching goal is to identify and develop durable exterior wood-frame walls to assist in the design and construction of energy efficient buildings across the country. Twelve test wall panels in six types of wall assemblies are assessed in this study. The wall panels, each measuring 4 ft. (1200 mm) wide and 8 ft. (2400 mm) tall, form portions of the exterior walls of a test hut located in the rear yard of FPInnovations’ Vancouver laboratory. This report, second in a series on this study, documents the performance of these wall assemblies based on the data collected over 19 months’ period from October 2018 to May 2020, covering two winter seasons and one summer.
The presented work deals with hygro-thermal numerical simulation and mould growth risk evaluation between concrete foundation and frame of multi-story building made of CLT element modules. Structural CLT modules represent an approach towards wood material utilization in construction as its strength achieves markedly higher values then common structural wooden elements and makes rapid erection of the building possible. Although there are great promises that the novel CLT structures will gain ground in high-rise buildings market with apparent benefits in sustainability and inhabitant comments regarding ambience and acoustics, it is important to analyse their structural health and hygro-thermal conditions. The highest risk of unfavourable hygro-thermal conditions is usually presented in location characterized by thermal bridge, such as foundation, window-wall, wall-roof and wall-floor junctions. It is also of significant importance to analyse junctions between materials, whether wood, composite, mortar or concrete. A certain combination of thermal and humidity conditions in exposed time causes mould growth initiation that may lead to deterioration of structural material and unhealthy indoor environment.
In this case study, the moisture content and air-flow in the junction and open space in structural design details between the first floor (of concrete) housing joint warehouse and technical spaces and the residential upper floors made of CLT modules is analysed. Conditions leading to probable moisture-derived mould issues and design parameters leading to sufficient ventilation according to Mould Index modelling are presented.
In this work the behaviour of hybrid multi-storey buildings braced with Cross-Laminated-Timber (CLT) cores and shear-walls is studied based on numerical analyses. Two procedures for calibrating numerical models are adopted and compared to test data and application of provisions in current design codes. The paper presents calibration of parameters characterising connections used to interconnect adjacent CLT panels and building cores, and attach shear-walls to foundations or floors that act as eleveted diaphragms. Different case studies are analysed comparing the structural responses of buildings assembled with „standard" fastening systems (e.g. hold-downs and angle-brackets), or using a special X-RAD connection system. The aim is to characterize behaviours of connections in ways that reflect how they perform as parts of completed multi-storey superstructure systems, rather than when isolated from such systems or their substructures. Results from various analyses are presented in terms of principal elastic periods, base shear forces, and uplift forces in buildings. Discussion addresses key issues associated with engineering analysis and design of buildings having around five or more storeys.