New Zealand Society for Earthquake Engineering Conference
April 13-15, 2012, Christchurch, New Zealand
The Nelson Marlborough Institute of Technology Arts and Media building was completed in 2011 and consists of three seismically separate complexes. This research focussed on the Arts building as it showcases the use of coupled post-tensioned timber shear walls. These are part of the innovative Expan system. Full-scale, in-situ dynamic testing of the novel building was combined with finite element modelling and updating to obtain an understanding of the structural dynamic performance within the linear range. Ambient testing was performed at three stages during construction and was combined with forced vibration testing for the final stage. This forms part of a larger instrumentation program developed to investigate the wind and seismic response and long term deformations of the building. A finite element model of the building was formulated and updated using experimental modal characteristics. It was shown that the addition of non-structural elements, such as cladding and the staircase, increased the natural frequency of the first mode and the second mode by 19% and 24%, respectively. The addition of the concrete floor topping as a structural diaphragm significantly increased the natural frequency of the first mode but not the second mode, with an increase of 123% and 18%, respectively. The elastic damping of the NMIT building at low-level vibrations was identified as being between 1.6% and 2.4%
The ambient movement of three modern multi-storey timber buildings has been measured and used to determine modal properties. This information, obtained by a simple, unobtrusive series of tests, can give insights into the structural performance of these forms of building, as well as providing information for the design of future, taller timber buildings for dynamic loads. For two of the buildings, the natural frequency has been related to the lateral stiffness of the structure, and compared with that given by a simple calculation. In future tall timber buildings, a new design criterion is expected to become important: deflection and vibration serviceability under wind load. For multi-storey timber buildings there is currently no empirical basis to estimate damping for calculation of wind-induced vibration, and there is little information for stiffness under wind load. This study therefore presents a method to address those gaps in knowledge.
In order to address the lack of measured natural frequencies and damping ratios for wood and hybrid wood buildings, and lack of knowledge of vibration performance of innovative CLT floors and sound insulation performance of CLT walls and floors, FPInnovations conducted a series of performance testing at the Wood Innovation Design Centre (WIDC) in Prince George, BC in April 2014, during construction, and in May 2015, after building completion and during its occupation.
This report describes the building, tested floor and wall assemblies, test methods, and summarizes the test results. The preliminary performance data provides critical feedback on the design of the building for resisting wind-induced vibration and on the floor vibration controlled design. The data can be further used to validate the calculation methods and tools/models of dynamic analysis.
Soft-story wood-frame buildings have been recognized as a disaster preparedness problem for decades. There are tens of thousands of these multi-family three- and four-story structures throughout California and other cities in the United States. The majority were constructed between 1920 and 1970, with many being prevalent in the San Francisco Bay Area in California. The NEES-Soft project was a five-university multi-industry effort that culminated in a series of full-scale soft-story wood-frame building tests to validate retrofit philosophies proposed by (1) the Federal Emergency Management Agency (FEMA) P-807 guidelines and (2) a performance-based seismic retrofit (PBSR) approach developed within the project. Four different retrofit designs were developed and validated at full-scale, each with specified performance objectives, which were typically not the same. This paper focuses on the retrofit design using cross laminated timber (CLT) rocking panels and presents the experimental results of the full-scale shake table test of a four-story 370 m2 (4000 ft2) soft-story test building with that FEMA P-807 focused retrofit in place. The building was subjected to the 1989 Loma Prieta and 1992 Cape Mendocino ground motions scaled to 5% damped spectral accelerations ranging from 0.2 to 0.9 g.
Mass timber is a generic name for a broad range of thick and heavy wood products such as cross-laminated timber (CLT), dowel-laminated timber (DLT), nail-laminated timber (NLT), and gluelaminated timber (GLT), among others. So far, vibration-controlled design methods have been developed mostly for CLT floors.
It has been shown that measurement of elastic constants of orthotropic wood-based panel products can be more efficiently measured by modal testing technique. Identification of vibration modes and corresponding natural frequencies is key to the application of modal testing technique. This process is generally tedious and requires a number of measurement locations for mode shape identification. In this study, a simplified method for frequency identification was developed which will facilitate the adoption of the vibration-based testing technique for laboratory and industrial application. In the method, the relationship between frequency order and mode order is first studied considering the boundary condition, elastic properties of the orthotropic panel. An algorithm is proposed to predict the frequency values and mode indices based on corresponding normalized sensitivity to elastic constants, initial estimates of orthotropic ratios and measured fundamental natural frequency. The output from the algorithm can be used for identification of sensitive natural frequencies from up to three frequency spectra. Then the algorithm is integrated with the elastic calculation algorithm to extract the elastic constants from the sensitive frequencies. The elastic constants of cross laminated timber panels were measured by the proposed method. The moduli of elasticity agree well with static testing results. The calculated in-plane shear modulus was found to be within the expected range.
This research paper deals with the evaluation of the dynamic modal vibration tests conducted on an innovative timber structure, the ETH House of Natural Resources. The building serves as a demonstrator of several innovative structural systems and technologies relating to timber. The main load-bearing structure comprises a posttensioned timber frame, which was subjected to modal vibration tests, firstly in the laboratory and, subsequently on the construction site. In this paper, the modal characteristics (eigenfrequencies, damping ratios and mode shapes), obtained from the laboratory testing campaign are presented. The modal vibration data is evaluated using polynomial and subspace identification techniques. The obtained results reveal that the structure exhibits pure translational, beam and column modes, as well as mixed beam-column modes. The bottom connection of the columns delivers significant influence on the modal characteristics, whereas the level of post-tensioning force yields no substantial influence in the modal characteristics obtained from low amplitude modal vibration tests.