This paper discusses the state-of-the-art of displacement-based seismic design (DBD) methods and their applications to timber buildings. First, an in-depth review of the DBD methods is presented, focusing in particular on the direct, modal and N2 methods. Then, paper presents DBD application on a wide range of construction systems, including both traditional light-frame structures as well as the emerging sector of tall and hybrid timber buildings. Finally, potentials of using these DBD methods for seismic design as well as possible implications of including DBD within the next generation of building codes are discussed.
This thesis studies the behaviour of diaphragms in multi-storey timber buildings by providing methods for the estimation of the diaphragm force demand, developing an Equivalent Truss Method for the analysis of timber diaphragms, and experimentally investigating the effects of displacement incompatibilities between the diaphragm and the lateral load resisting system and developing methods for their mitigation.
Although shortcomings in the estimation of force demand, and in the analysis and design of concrete floor diaphragms have already been partially addressed by other researchers, the behaviour of diaphragms in modern multi-storey timber buildings in general, and in low damage Pres-Lam buildings (consisting of post-tensioned timber members) in particular is still unknown.
The analysis of light timber framing and massive timber diaphragms can be successfully analysed with an Equivalent Truss Method, which is calibrated by accounting for the panel shear and fastener stiffnesses. Finally, displacement incompatibilities in frame and wall structures can be accommodated by the flexibilities of the diaphragm panels and relative connections. A design recommendations chapter summarizes all findings and allows a designer to estimate diaphragm forces, to analyse the force path in timber diaphragms and to detail the connections to allow for displacement incompatibilities in multi-storey timber buildings.
The acceptable solutions in Division B of the anticipated 2020 NBCC limit the height of Groups C and D buildings of sprinklered encapsulated mass timber construction (EMTC) to 12 storeys in building height, and a measured building height of 42m. The recently published 2021 IBC contains provisions to permit buildings of mass timber construction under the IBC Type IV construction, surpassing the NBCC provisions by maximum building height, building area, occupancy groups, and interior exposed timber. The IBC mass timber buildings are permitted to have a building height of maximum 18 storeys, depending on the occupancy group. Within Type IV construction, four subdivisions are described to have varying maximum permissible building height, area, fire resistance rating (FRR), and interior exposed timber.
Through a comparison of mass timber provisions of both Codes, relevant research reports, test reports, industry standards, this report documents the consequential and inconsequential differences and developed conclusions on whether the NBCC can adopt the IBC provisions, and with what modifications so that the new provisions may fit the NBCC context.
In this paper, we discuss the structural design of one of the tallest timber-based hybrid buildings in the world: the 18 storey, 53 meter tall student residence on the campus of the University of British Columbia in Vancouver. The building is of hybrid construction: 17 storeys of mass wood construction on top of one storey of concrete construction. Two concrete cores containing vertical circulation provide the required lateral resistance. The timber system is comprised of cross-laminated timber panels, which are point supported on glued-laminated timber columns and steel connections between levels. In addition to providing more than 400 beds for students, the building will serve as an academic site to monitor and study its structural performance, specifically horizontal building vibration and vertical shrinkage considerations. We present the challenges relating to the approval process of the building and discuss building code compliance issues.
Recent years have seen more architects and clients asking for tall timber buildings. In response, an ambitious timber community has been proposing challenging plans and ideas for multi-storey commercial and residential timber buildings. While engineers have been intensively looking at gravity-load-carrying elements as well as walls, frames and cores to resist lateral loads, floor diaphragms have been largely neglected.
Complex floor geometries and long span floor diaphragms create stress concentrations, high force demand and potentially large deformations. There is a lack of guidance and regulation regarding the analysis and design of timber diaphragms so structural engineers need a practical alternative to simplistic equivalent deep beam analysis or costly finite element modelling.
This paper proposes an equivalent truss method capable of solving complex geometries for both light timber framing and massive timber diaphragms. Floor panels are discretized by equivalent diagonals, having the same stiffness as the panel including its fasteners. With this method the panel unit shear forces (shear flow) and therefore fastener demand, chord forces and reaction forces can be evaluated. Because panel stiffness is accounted for, diaphragm deflection, torsional effects and transfer forces can also be assessed.
This building is a typical one-storey commercial building located in Vancouver, BC. The plan dimensions are 30.5 m x 12.2 m (100’ x 40’), with a building height of 5 m. The walls are wood-based shear walls, with a wood diaphragm roof and a steel moment frame at the storefront. The roof plan is shown in Figure 1. The site is Seismic Class ‘C’. Wind, snow and seismic figures specific to the project location are taken from the current version of the British Columbia Building Code (2012). Roof dead load is assumed to be 1.0 kPa and the wall weight is 0.5 kPa. The weight of non-structural items including mechanical equipment and the storefront façade has not been included in this example for simplicity.
This paper reflects on the structural design of Haut; a 21-storey high-end residential development in Amsterdam, the Netherlands. Construction started in 2019 and is in progress at the time of writing. Upon completion in 2021, Haut will be the first residential building in the Netherlands to achieve a 'BREEAM-outstanding' classification. The building will reach a height of 73 m, making it the highest timber structure in the Netherlands. It contains some 14.500 of predominantly residential functions. It features a hybrid concrete-timber stability system and concrete-timber floor panels. This paper describes the concepts behind the structural design for Haut and will touch upon the main challenges that have arisen from the specific combination of characteristics of the project. The paper describes the design of the stability system and -floor system, the analysis of differential movements between concrete and timber structures and wind vibrations. The paper aims to show how the design team has met these specific challenges by implementing a holistic design approach and integrating market knowledge at an early stage of the design.
Tall wood buildings have been at the foreground of innovative building practice in urban contexts for a number of years. From London to Stockholm, from Vancouver to Melbourne timber buildings of up to 20 storeys have been built, are under construction or being considered. This dynamic trend was enabled by developments in the material itself, prefabrication and more flexibility in fire regulations. The low CO2 footprint of wood - often regionally sourced - is another strong argument in its favour. This publication explains the typical construction types such as panel systems, frame and hybrid systems. An international selection of 13 case studies is documented in detail with many specially prepared construction drawings, demonstrating the range of the technology.