A cross-laminated timber (CLT) wall plays the role of resisting shear stress induced by lateral forces as well as vertical load. Due to the press size, CLT panels have a limitation in size. To minimize the initial investment, some glulam manufactures wanted to make a shear wall element with small-size CLT panels and panel-to-panel connections and wanted to know whether the shear wall would have equivalent shear performance with the wall made of a single CLT panel. In this study, this was investigated by experiments and kinematic model analysis. Two shear walls made of small CLT panels were tested. The model showed a good agreement with test results in the envelope curve. Even though the shear walls were made of small panels, the global peak load did not decrease significantly compared with the wall made of a single CLT panel, but the global displacement showed a large increase. From this analysis, it was concluded that the shear wall can be designed with small CLT panels, but displacement should be designed carefully.
In this paper, the results of lateral loading tests on two types of CLT shear wall systems with an opening are summarized, one is the shear wall system with assembling narrow size CLT panels and another is that using one large size panel with an opening. 8 types, 13 specimens in all were tested. Load-displacement curves were obtained and characteristic values of shear performance were derived. As a result, the assembly system revealed higher ductility because of the ductility of connections between panels, while the rapture of large panel system was brittle though the shear capacity was higher than the assembly system.
In the last decade, cross laminated timber (CLT) has been receiving increasing attention as a promising construction material for multi-storey structures in areas of high seismicity. In Japan, application of CLT in building construction is still relatively new; however, there is increasing interest in CLT from researchers as well as construction companies. Furthermore, the Japanese government is providing construction cost subsidies for new CLT structures as it is a carbon neutral and sustainable material. The high shear and compressive strength of CLT makes it a good candidate for use as shear walls in mid-rise buildings. One important aspect of CLT walls, and one that is presently poorly understood, is the influence of openings on the shear carrying capacity. Openings are often necessary in CLT panels either in form of windows, doors, lift shaft openings or installation of building services. Concerning this aspect, the code regulations in Japan are relatively strict, such that if openings exceeded certain prescribed limits, the entire CLT panel is considered as a non-structural element, and its contribution to lateral strength is totally ignored. Furthermore, as the maximum opening size is usually governed by edge distance constraints, the size of openings that designers can use is inevitably limited by the standard sizes supplied by the manufacturers. As a result, designers are obligated to adopt very small opening size. This is thought to be a very conservative approach. The main purpose of this paper is to experimentally evaluate the influence of openings on seismic capacity; strength and stiffness reduction, as well as failure mode with changing opening size and opening aspect ratio. In addition, check the validity of the Japanese code regulations with regards to openings in CLT panels.
In this study, six 5-layer CLT panels containing different openings were tested. The parameters considered include the size and layout of the opening. The panels were specifically designed with openings that would render them ineffective in resisting lateral loads according to the Japanese standard. However, in addition to the six panels, one panel without openings and one panel with openings that meet the Japanese standard was designed. All the CLT panels were tested in uniaxial diagonal compression in order to simulate pure shear loading. The CLT panels and the loading setup were designed such that the resulting failure mode will be governed by a shear mechanism. The main focus of the experiment was to relate the deterioration of the lateral strength and stiffness of the panels to the size and layout of the opening.
The results showed that the panels with openings with the same area have relatively different failure direction and reduction factors for panel shear strength and stiffness, and that is due to the shear weak and strong direction that CLT panels have. Also, the effect of openings on the reduction of stiffness for CLT panels was found to be greater than their effect on the reduction of shear strength. The prescribed equation in the Japanese CLT Guidebook underpredicts stiffness reduction, and has discrepancies with regard to strength as the difference of panel strengths in weak and strong directions are not considered.
Recently, the numerical value and the technical information of the design are insufficient though an increase of a large timber construction is expected. In this research, a high load carrying capacity shear wall with thick plywood sheathings for the large timber construction was developed, and its static bearing force was confirmed experimentally. And the bearing force of the shear wall was calculated by using past numerical analysis methods. As a result, the development of the wall having the target bearing force succeeded, and the numerical analysis method could be applied to the high load carrying capacity shear wall.
The latest developments in seismic design philosophy have been geared towards developing of so called "resilient" or "low damage" innovative structural systems that can reduce damage to the structure while offering the same or higher levels of safety to occupants. One such innovative structural system is the Pres-Lam system that is a wood-hybrid system that utilizes post-tensioned (PT) mass timber components in both rigid-frame and wall-based buildings along with various types of energy disspators. To help implement the Pres-Lam system in Canada and the US, information about the system performance made with North American engineered wood products is needed. That information can later be used to develop design guidelines for the designers for wider acceptance of the system by the design community.Several components influence the performance of the Pres-Lam systems: the load-deformation properties of the engineered wood products under compression, load-deformation and energy dissipation properties of the dissipators used, placement of the dissipators in the system, and the level of post-tensioning force. The influence of all these components on the performance of Pres-Lam wall systems under gravity and lateral loads was investigated in this research project. The research project consisted of two main parts: material tests and system tests.
The purpose of this study is to develop a high strength leg joint for shear wall made of small size cross laminated timber panel in a simple system. The joint of CLT in which steel plate was inserted in the central slit and fixed by high strength bolt at inside of short steel pipes was proposed. In order to grasp the failure mode and strength of CLT member, material tests on embedment and shear were carried out using small CLT blocks. The test results indicated that there is few reinforce effect by cross bonding of each lamina. It was concluded that the precise estimation of the strength of CLT member is important in order to develop the joint proposed in this paper.
Cross-laminated timber (CLT) is a relatively new type of massive timber system that has shown to possess excellent mechanical properties and structural behavior in building construction. When post-tensioned with high-strength tendons, CLT panels perform well under cyclic loadings because of two key characteristics: their rocking behavior and self-centering capacity. Although post-tensioned rocking CLT panels can carry heavy gravity loads, resist lateral loads, and self-center after a seismic event, they are heavy and form a pinched hysteresis, thereby limiting energy dissipation. Conversely, conventional light-frame wood shear walls (LiFS) provide a large amount of energy dissipation from fastener slip and, as their name implies, are lightweight, thereby reducing inertial forces during earthquakes. The combination of these different lateral behaviors can help improve the performance of buildings during strong ground shaking, but issues of deformation compatibility exist. This study presents the results of a numerical study to examine the behavior of post-tensioned CLT walls under cyclic loadings. A well-known 10-parameter model was applied to simulate the performance of a CLT-LiFS hybrid system. The posttensioned CLT wall model was designed on the basis of a modified monolithic beam analogy that was originally developed for precast concrete-jointed ductile connections. Several tests on post-tensioned CLT panels and hybrid walls were implemented at the Large Scale Structural Lab at the University of Alabama to validate the numerical model, and the results showed very good agreement with the numerical model. Finally, incremental dynamic analysis on system level models was compared with conventional light-frame wood system models.
Project contact is Y.H. Chui at the University of Alberta
Wood shear wall systems with insulated sheathing are commonly implemented to meet a higher standard of building energy efficiency. Adding a layer of continuous thermal insulation exterior to the cavity insulation, insulated sheathing, to reduce thermal bridging is getting more popular in practice. The impact of the intermediated insulation on racking performance of shear walls has recently been investigated by experimental studies. The test data provides better understanding on the influence of various construction configurations. Nevertheless, there is a need to provide an alternative approach which enables engineers to calculate the design capacities of shear walls with insulated sheathing. In this project, the available analytical models and approaches for determining shear resistances of shear walls are reviewed and compared. A new modified analytical model will be developed based on comparisons and the test results.
A cross-laminated timber (CLT) wall plays a role of resisting shear stress induced by lateral forces as well as resisting vertical load. Due to the press size, CLT panels have a limitation in its size. To minimize the initial investment, some glulam manufactures wanted to make a shear wall element with small-size CLT panels and panel-to-panel...
Project contact is Arijit Sinha at Oregon State University
Constructing buildings with CLT requires development of novel panel attachment methods and mechanisms. Architects and engineers need to know the engineering strength properties of connected panels, especially in an earthquake prone area. This project will improve knowledge of three types of wall panel connections: wall-to-floor, wall-to-wall, and wall-to-foundation. Testing will determine the strength properties of metal connectors applied with diffferent types and sizes of screw fasteners. The data will be used to develop a modeling tool that engineers can use when designing multi-story buildings to be constructed with CLT panels.